11
O R I G I N A L I N S T R U C T I O N S
GB
PRODUCT CHARACTERISTICS
The electric paint sprayer gun is an electrical device of II insulation class used for covering the surface with a coating material or lacquer.
Thanks to the built-in compressor, the gun does not need an external compressed air supply. Capacious paint container combined with
high performance ensure smooth operation. The correct, reliable and safe operation of the tool depends on its proper use, therefore:
Read and keep the entire manual before the
fi
rst use of the device.
The supplier will not be held liable for any damage resulting from failure to observe the safety regulations and recommendations
speci
fi
ed in this manual.
ACCESSORIES
The packaging should include: sprayer gun, paint container, viscometer.
TECHNICAL PARAMETERS
Parameter
Unit
Value
Catalogue No.
YT-82553
Power supply voltage
[V~]
220 - 240
Power frequency
[Hz]
50
Rated power
[W]
600
Electrical protection class
II
Weight
[kg]
1.3
Container capacity
[l]
1
Rated capacity
[l/min.]
1
Nozzle diameter
[mm]
2.6
Noise level
pressure L
pA
[dB(A)]
80.4 ± 3.0
power L
wA
[dB(A)]
91.4 ± 3.0
Vibration level a
h
[m/s
2
]
0.67 ± 1.5
Protection rating
IPX0
GENERAL SAFETY CONDITIONS
NOTE!
Get acquainted with all the instructions below. Failure to observe them may lead to an electric shock,
fi
re or injuries. The notion
of electric tool used in the instructions applies to all the tools which are powered with electric current, both wire tools and wireless ones.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be properly illuminated and clean.
Disorder and poor illumination may be a cause of accidents.
Do not work with electric tools in explosive environments, or those which contain in
fl
ammable liquids, gases or vapours.
Electric tools generate sparks, which may cause a
fi
re in case of contact with in
fl
ammable gases or vapours.
Do not allow children and outsiders to the place of work.
A lack of concentration may result in a loss of control over the tool.
Electric safety
The plug of the power supply cable must
fi
t the mains socket. Do not modify the plug. Do not use any adapters what-
soever in order to adapt the plug to the socket.
Unmodi
fi
ed plug which
fi
ts the socket reduces the risk of an electric shock.
Avoid contact with grounded surfaces, such as pipes, heaters and refrigerators.
Grounding of the body increases the risk
of an electric shock.
Do not expose electric tools to precipitation or humidity.
Water and humidity which gets into the electric tool increases the
risk of an electric shock.
Do not overload the power supply cable. Do not use the power supply cable in order to carry the tool or to connect and
disconnect the plug from the mains socket. Avoid contact of the power supply cable with heat, oils, sharp tools and
moving elements.
Damage to the power supply cable increases the risk of an electric shock.
In case work is realised outside closed areas, it is necessary to use extension cords designed for applications outside
closed areas.
Using a correct extension cord permits to reduce the risk of an electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RDC) protected supply.
Use of
an RCD reduces the risk of electric shock.
Summary of Contents for YT-82553
