18
EN
O R I G I N A L I N S T R U C T I O N S
If a two-piece attachment is used, the guide link (XVI) must be
fi
tted
fi
rst and then the guide mounted to it so that the guide sole
is under the tool foot (XVII). The distance “L” between the guide plate and the edge of the blade will be the width of the rebate
(XVIII). Start working on the wooden surface as for planing. The guide plate should always be against the edge of the surface to
be machined (XIX).
It is recommended to gradually deepen the rebate to the planned depth.
Additional notes
After
fi
nishing work, switch o
ff
the tool, detach the battery and perform maintenance and inspection.
The tool is equipped with a storage compartment to hold the wrenches needed to remove and install the planer blades (XX).
MAINTENANCE AND OVERHAUL
ATTENTION! Before any adjustment, technical service or maintenance operations unplug the tool. Once the operations have been
fi
nished, the technical conditions of the tool must be assessed by means of external evaluation and inspection of the following
elements: body and handle, conductor with a plug and de
fl
ection, functioning of the electric switch, patency of ventilation slots,
sparking of brushes, noise level of functioning of bearings and gears, start-up and smoothness of operation. During the guarantee
period, the user cannot dismantle the electric tools or change any sub-assemblies or elements, since it will cancel any guarantee
rights. All irregularities detected at overhaul or during functioning of the tools are a signal to have the tool repaired at a service
shop. Once the functioning has been concluded, the casing, ventilation slots, switches, additional handle and protections must be
cleansed with a stream of air (at a pressure not exceeding 0.3 MPa), with a brush or a cloth without any chemical substances or
cleaning liquids. Tools and handles must be cleansed with a clean cloth.
Summary of Contents for YT-82192
