MD7-EUenAB-2110(8)
Page 7/11
2021-10-11 Rev. 8
MD7-EUenAB-2110(8)
Page 8/11
2021-10-11 Rev. 8
Troubleshooting
Problem
Possible cause
Solution
LED does not illuminate
LED switch button not pressed.
Press LED switch button.
Wrong battery polarity.
Check battery polarity and set correctly
(refer to “Assembly”).
Batteries have run out.
Replace with charged or new batteries.
Tail cap not firmly tightened.
Firmly tighten tail cap.
Serial number label in battery compartment
has peeled off and is blocking the battery
terminals.
Remove serial number label.
Water has entered the battery compartment
and caused a circuit malfunction.
Contact the distributor.
Cannot press the LED
switch button
Temperature too low.
Warm the tail cap.
Flickering/weak light
Tail cap not firmly tightened.
Firmly tighten tail cap.
Batteries have run down.
Replace with charged or new batteries.
Short battery run time
Electrical contact failures.
Clean electrical contacts of the light
handle, tail cap, and batteries using a dry
cloth or cotton swab.
Small battery capacity.
Replace with larger-capacity batteries
(NiMH rechargeable batteries of
≥
900
mAh capacity are recommended).
Product too hot
Light handle may be damaged.
Stop using the device immediately and
contact the distributor.
Contact your local distributor if the problem still exists after applying the solutions above. Repairs must be conducted by
the authorized persons of the manufacturer.
Appendices
Specifications
•
Product name: koplight blade
Model
code
Tip width
(mm)
Blade length
(mm)
Total length
(mm)
KS-1
10
30
139
KS-2
13
45
139
KS-3
18
45
139
KS-4
18
59
113
KS-5
25
84
113
Material: Polycarbonate
•
Product name: koplight HT blade
Model
code
Tip width
(mm)
Blade
length
(mm)
Total length
(mm)
KS-4H
18
61
122
KS-5H
25
86
122
KS-6H
25
111
122
Material: Polycarbonate
•
Product name: koplight light handle
Model code
KG-1
Material
Body:
Anodized aluminum
Lens:
Polycarbonate
LED switch button: Fluorine resin
Battery
2 × AAA nickel-metal hydride (NiMH) rechargeable battery
Recommended battery
Manufacturer:
FDK CORPORATION
Model code:
HR-4UTHC
Nominal voltage:
1.2 V
Battery capacity:
900 mAh
Rated input
2.4 V DC
LED
Color temperature: 5,000 K
Note: There are slight variances in the color temperature and brightness of the LED.
Dimension
Diameter: 15 mm (narrowest point) × Total length: 155 mm
Operating/storage
temperature
0 °C to 40 °C
Note: Recommended operating temperature range is 15 °C to 40 °C. Waterproof
performance degrades in between 0 °C to 15 °C due to hardened O-ring.
Recommended to store at room temperature.
Relative humidity
30% to 90%, non-condensing
Atmospheric pressure
70 kPa to 106 kPa
Storage/Transfer
condition
Remove batteries
•
Accessories
Product name
Model
code
Material
koplight light handle finger hook
KY-1
Polycarbonate
koplight light handle O-ring
KP-1
Fluorine resin
koplight battery inserter
KD-1
Polycarbonate
Retail packaging
Product name
Content
koplight blade/koplight HT blade
12 × blades per package.
koplight light handle
1 × light handle, 1 × finger hook, 1 × O-ring, 1 × battery inserter per package.
Note: Batteries are not included.
Safety classifications
Protection against electrical shock
Internally powered ME equipment
Degree of protection against electric shock
Blade is type BF applied part
Method of sterilization or disinfection
Refer to "Cleaning and disinfection" and "Sterilization"
Degree of protection against ingress of water
(IEC 60529)
IPX7
This product is not for use in an oxygen rich environment.
Precautions for
interference with other equipment
In order to avoid LED lighting malfunction caused by interference with other equipment:
•
Keep away from portable wireless communication devices such as cellular phones by more than 30 cm.
•
Do not use close to or stacked on other equipment.
•
If electrosurgical instruments can cause malfunctions, try not to use them at the same time.
Note: No malfunction will occur when the device comes into contact with an electric scalpel. Electrosurgical
instruments are generally compatible with the device, but some may cause malfunctions. For further information, refer
to “Electromagnetic Compatibility (EMC).”
Electromagnetic Compatibility (EMC)
This product complies with EMC Standard EN60601-1-2: 2015. This product is intended for use in the electromagnetic
environment specified in the following tables. The following problems may be encountered if the product is used in an
unintended environment:
•
LED light does not turn on.
•
LED light turns on, but flickering occurs.
•
LED light turns on, but there is a significant increase or decrease in illumination that can be visually confirmed.
•
LED switch button does not work.
