Mode
Contents
Operator Display
Description
Drive Mode
Frequency
Reference
- MODE -
U1-01= 0.00Hz
U1-02= 0.00Hz
U1-03= 0.00A
DRV
FREF (AI)
Rdy
RSEQ
RREF
FWD
JOG
Returns to the frequency reference display screen.
n
Drive Mode Details
The following actions are possible in the Drive Mode:
• Run and stop the drive
• Monitor the operation status of the drive (frequency reference, output frequency, output current, output voltage, etc.)
• View information on an alarm
• View a history of alarms that have occurred
This example assumes the drive is set to LOCAL.
ESC
F1
F2
←
→
←
→
←
→
- MODE -
U1-01= 0.00Hz
U1-02= 0.00Hz
U1-03= 0.00A
DRV
FREF (AI)
Rdy
RSEQ
RREF
Frequency reference
display at power up
Press until the frequency
reference changes to 006.00 Hz
left
right
Press to select
LOCAL
- MODE -
U1-01= 0.00Hz
U1-02= 0.00Hz
U1-03= 0.00A
DRV
FREF (OPR)
Rdy
JOG
FWD
FWD/REV
LSEQ
LREF
- MODE -
U1-01= 6.00Hz
U1-02= 0.00Hz
U1-03= 0.00A
DRV
FREF (OPR)
Rdy
JOG
FWD
FWD/REV
LSEQ
LREF
-MONITR-
FREF (d1-01)
U1-01=
0
00.00Hz
(
0.00
~
60.00
)
“
0.00Hz
”
DRV
FWD
Rdy
-MONITR-
FREF (d1-01)
U1-01= 00
6
.00Hz
(
0.00
~
60.00
)
“
0.00Hz
”
DRV
FWD
Rdy
-MONITR-
FREF (d1-01)
U1-01= 00
6
.00Hz
(
0.00
~
60.00
)
“
0.00Hz
”
DRV
FWD
Rdy
Entry Accepted
FWD
JOG
Figure 4.6 Setting the Frequency Reference while in the Drive Mode
Note:
The drive will not accept a change to the frequency reference until the ENTER key is pressed after the frequency reference is entered. This
feature prevents accidental setting of the frequency reference. To have the drive accept changes to the frequency reference as soon as changes
are made without requiring the ENTER key, set o2-05 to 1.
n
Programming Mode Details
The following actions are possible in the Programming Mode:
•
Parameter Setting Mode:
Access and edit all parameter settings.
•
Verify Menu:
View a list of parameters that have been changed from the default values.
•
Setup Group:
Access a list of commonly used parameters to simplify setup (
Refer to Simplified Setup Using the Setup
).
•
Auto-Tuning Mode:
Automatically calculate and set motor parameters to optimize drive performance.
u
Changing Parameter Settings or Values
This example explains changing C1-02 (Deceleration Time 1) from 10.0 seconds to 20.0 seconds.
Step
Display/Result
1.
Turn on the power to the drive. The initial display appears.
- MODE -
U1-01= 0.00Hz
U1-02= 0.00Hz
U1-03= 0.00A
DRV
FREF (AI)
Rdy
RSEQ
RREF
FWD
JOG
2.
Press
or
until the Parameter Setting Mode screen appears.
HELP
- MODE -
PRG
DATA
Programming
FWD
4.3 The Drive and Programming Modes
YASKAWA ELECTRIC SIEP C710636 04D U1000 Industrial MATRIX Drive Technical Manual
141
4
Start-Up Programming & Operation
Summary of Contents for U1000 iQpump Drive
Page 705: ......