Model
Terminal
For USA and Canada
For South America
Screw
Size
Tightening
Torque
N·m (lb.in.)
Recomm. Gauge
mm
2
(AWG, kcmil)
Wire Range
mm
2
(AWG, kcmil)
Recomm. Gauge
mm
2
(AWG, kcmil)
Wire Range
mm
2
(AWG, kcmil)
EUJ71182
o
.
o
R/L1, S/L2, T/L3
95 × 8P
(4/0 × 8P)
95 to 150 × 8P
(4/0 to 300 × 8P)
150 × 4P
(300 × 4P)
150 × 4P
(300 × 4P)
M12
31.4 to 39.2
(278 to 347)
X, Y, Z
95 × 8P
(4/0 × 8P)
95 to 150 × 8P
(4/0 to 300 × 8P)
150 × 4P
(300 × 4P)
150 × 4P
(300 × 4P)
M12
31.4 to 39.2
(278 to 347)
X1, Y1, Z1
50
(1/0)
50 to 70
(1/0 to 2/0)
35
(1)
35 to 50
(1 to 1/0)
M8
5.4 to 6.0
(47.8 to 53.0)
95
(4/0)
95 to 150
(4/0 to 300)
150 × 2P
(300 × 2P)
150 × 2P
(300 × 2P)
M12
31.4 to 39.2
(278 to 347)
r1, s1, t1
2.5
(14)
2.5 to 4
(14 to 12)
2.5
(14)
2.5 to 4
(14 to 12)
M4
1.2 to 2.0
(10.4 to 17.4)
p2, n2
2.5
(14)
2.5 to 4
(14 to 12)
2.5
(14)
2.5 to 4
(14 to 12)
M4
1.2 to 2.0
(10.4 to 17.4)
<1> Take additional measures in accordance with IEC/EN 61800-5-1 when wiring an EMC filter is installed.
Refer to EMC Filter Installation on page
u
Main Circuit Terminal and Motor Wiring
This section outlines the various steps, precautions, and checkpoints for wiring the main circuit terminals and motor terminals.
NOTICE: When connecting the motor to the drive output terminals U/T1, V/T2, and W/T3, the phase order for the drive and motor should
match. Failure to comply with proper wiring practices may cause the motor to run in reverse if the phase order is backward.
NOTICE: Route motor leads U/T1, V/T2, and W/T3 separate from all other leads to reduce possible interference related issues. Failure to
comply may result in abnormal operation of drive and nearby equipment.
n
Cable Length Between Drive and Motor
Voltage drop along the motor cable may cause reduced motor torque when the wiring between the drive and the motor is too
long, especially at low frequency output. This can also be a problem when motors are connected in parallel with a fairly long
motor cable. Drive output current will increase as the leakage current from the cable increases. An increase in leakage current
may trigger an overcurrent situation and weaken the accuracy of the current detection.
Adjust the drive carrier frequency according to
. If the motor wiring distance exceeds 100 m because of the system
configuration, reduce the ground currents.
Refer to C6-02: Carrier Frequency Selection on page 234
Table 3.8 Cable Length Between Drive and Motor
Cable Length
50 m or less
Greater than 50 m
Carrier Frequency
10 kHz or less
4 kHz or less
Note:
1.
When setting carrier frequency for drives running multiple motors, calculate cable length as the total wiring distance to all connected
motors.
2.
The maximum cable length when using OLV/PM (A1-02 = 5) or AOLV/PM (A1-02 = 6) is 100 m.
n
Ground Wiring
Follow the precautions below when wiring the ground for one drive or a series of drives.
WARNING! Electrical Shock Hazard. Always use a ground wire that complies with technical standards on electrical equipment and minimize
the length of the ground wire. Improper equipment grounding may cause dangerous electrical potentials on equipment chassis, which could
result in death or serious injury.
WARNING! Electrical Shock Hazard. Be sure to ground the drive ground terminal (200 V class: ground to 100 Ω or less; 400 V class: ground
to 10 Ω or less). Improper equipment grounding could result in death or serious injury by contacting ungrounded electrical equipment.
NOTICE: Do not share the ground wire with other devices such as welding machines or large-current electrical equipment. Improper
equipment grounding could result in drive or equipment malfunction due to electrical interference.
NOTICE: When using more than one drive, ground multiple drives according to instructions. Improper equipment grounding could result in
abnormal operation of drive or equipment.
Refer to
when using multiple drives or when using multiple drive models 4
o
0720 to 4
o
0930 that are connected
with harmonic filter module. Do not loop the ground wire.
3.8 Main Circuit Wiring
YASKAWA ELECTRIC SIEP C710636 04D U1000 Industrial MATRIX Drive Technical Manual
105
3
Electrical Installation
Summary of Contents for U1000 iQpump Drive
Page 705: ......
