YASKAWA CIMR-RB Series, Instruction Manual

Page: 10 / 209

10 YASKAWA ELECTRIC TOEP C710656 10B YASKAWA Power Regenerative Unit - R1000 Instruction Manual
i.1 Preface
i.1 Preface
Yaskawa manufactures products used as components in a wide variety of industrial systems and equipment. The selection
and application of Yaskawa products remain the responsibility of the equipment manufacturer or end user. Yaskawa
accepts no responsibility for the way its products are incorporated into the final system design. Under no circumstances
should any Yaskawa product be incorporated into any product or design as the exclusive or sole safety control. Without
exception, all controls should be designed to detect faults dynamically and fail safely under all circumstances. All
systems or equipment designed to incorporate a product manufactured by Yaskawa must be supplied to the end user with
appropriate warnings and instructions as to the safe use and operation of that part. Any warnings provided by Yaskawa
must be promptly provided to the end user. Yaskawa offers an express warranty only as to the quality of its products in
conforming to standards and specifications published in the Yaskawa manual. NO OTHER WARRANTY, EXPRESS OR
IMPLIED, IS OFFERED. Yaskawa assumes no liability for any personal injury, property damage, losses, or claims
arising from misapplication of its products.
This manual is designed to ensure correct and suitable application of R1000-Series Regenerative Units. Read this manual
before attempting to install, operate, maintain, or inspect a regenerative unit and keep it in a safe, convenient location for
future reference. Be sure you understand all precautions and safety information before attempting application.
◆
Applicable Documentation
The following manuals are available for R1000 series:
◆
Symbols
Note: Indicates a supplement or precaution that does not cause regenerative unit damage.
◆
Terms and Abbreviations
• Regenerative Unit : YASKAWA R1000 Series Power Regenerative Unit
• Drive : Yaskawa 1000-Series Drive
• BCD : Binary Coded Decimal
• H : Hexadecimal Number Format
• IGBT : Insulated Gate Bipolar Transistor
◆
Trademarks
• MECHATROLINK-I/MECHATROLINK-II are trademarks of MECHATROLINK Members Association (MMA).
• Other companies and product names mentioned in this manual are trademarks of those companies.
YASKAWA R1000 Series
Power Regenerative Unit
Instruction Manual (TOEP C710656 10)
This guide is packaged together with the product and contains basic information required to install and wire the
regenerative unit. It also gives an fault diagnostics, maintenance, and parameter settings. The purpose of this guide is to
prepare the regenerative unit for a trial run with an application and for basic operation.
LO
RE
ESC
RUN STOP
ENTER RESET
ALM DIGITAL OPERATOR JVOP-182
CIMR-AA2A0021FAA
200V 3Phase 5.5kW/3.7kW
REV DRV FOUT
S/N:
危 険
据え付け、運転の前には必ず取扱説明書を読むこと。
通電中および電源遮断後
5 分以内はフロントカバー
を外さない事。
400V 級インバータの場合は、電源の中性点が接地
されていることを確認すること。( 対応）
保守・点検、配線を行う場合は、出力側開閉器を
遮断後
5 分待って実施してください。
けが．感電のおそれがあります。
高温注意
インバータ上部、両側面は高温になります。
触らないでください。
●
●
●
●
●
AVERTISSMENT NPJT31470-1
Lire le manuel avant l'installation.
Attendre 5 minutes après la coupure
de l'alimentation, pour permettre
la décharge des condensateurs.
Pour répondre aux exigences , s
assurer que le neutre soit relié
à la terre, pour la série 400V.
Après avoir déconnécte la protection
entre le driver et le moteur, veuillez
patienter 5 minutes avain d’effectuer
une opération de montage ou de
câblage du variateur.
Risque de décharge électrique.
Surfaces Chaudes
Dessus et cotés du boitier Peuvent
devenir chaud. Ne Pas toucher.
WARNING
Read manual before installing.
Wait 5 minutes for capacitor
discharge after disconnecting
power supply.
To conform to requirements,
make sure to ground the supply
neutral for 400V class.
After opening the manual switch
between the drive and motor,
please wait 5 minutes before
inspecting, performing
maintenance or wiring the drive.
Risk of electric shock.
Hot surfaces
Top and Side surfaces may
become hot. Do not touch.
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
VDC Reference : v 0(V)
⋥ᵹᲣ✢㔚࿶ᜰ઎
VDC FeedBack : 0(V)
⋥ᵹᲣ✢㔚࿶Ꮻㆶ
DC Current Ref : 0.0A(A)
⋥ᵹ㔚ᵹᜰ઎
VAC Voltage : 0v(V)
㔚Ḯ㔚࿶
Selected Monitor : 0.0(Hz)
㔚Ḯ๟ᵄᢙ
Monitor : Mon
ࡕ࠾࠲
Verify : vrFY
ࡌ࡝ࡈࠔࠗ
SetUpGuide : STUP
࠮࠶࠻ࠕ࠶ࡊ
Parameter Set : PAr
ࡄ࡜ࡔ࡯࠲⸳ቯ
TOEP_C710656_10B_1_0.book 10 ページ ２０１５年１月８日 木曜日 午後８時５５分