background image

PRODUCT SPECIFICATIONS 

Model: SN70016

-1

 

Power Supply Voltage:  120V-60Hz 

      Sweep Width: 

  16 in. (406 mm) 

Idle Speed: 

4500 RPM 

      Max Clearing Depth:    8 in. (200 mm) 

Power Consumption:  12 Amp  

      Throwing Distance:     Up to 30 ft. 

Weight:  

14.5 lbs. 

      Clearing Capacity:     430 lbs./minute 

Model SN70016-1 SKU 270-3286

PACKING LIST 

  UNPACKING 

Carefully remove the product from the box. 

Make sure that all items listed in the packing 

list are included. 
Inspect all items carefully to make sure no 

breakage or damage occurred during shipping. 
Do not discard the packing material until you 

have carefully inspected and satisfactorily   

operated the snow thrower. 
If any parts are damaged or missing please  

call our customer service help line at     

1-800-633-1501 for assistance.

QTY 

DESCRIPTION 

Snow Thrower 

Lower & Upper Handle 

M6x45

 Carriage Bolt & Wing Nut 

ST4.2x30 

Philips Head Self Tapping 

Screw  

Adjust Knob 

ST3.9x55 

Philips Head Self Tapping 

Screw  

Adjust Knob Cover 

Wheel Bracket 

Wheel 

Hub Cap 

Auxiliary Handle 

M6x50 

Hex Head Bolt & Wing Nut 

Operator’s Manual 

Summary of Contents for SN70016-1















Reviews: