background image

8

CONCRETE FOUNDATION 

Your kit contains all materials to construct a wooden floor. If you choose to install your kit

 

on a concrete slab refer to the diagram below.

• A treated 2 x 4" (5,1 x 10,2 cm) sill plate is required when installing your shed on concrete. 

Hint: Use treated lumber in your kit or

 

   purchase full length treated lumber.

 

 

• Use a high quality exterior grade caulk beneath all sill plates.

 

 

• Fasten 2 x 4" (5,1 x 10,2 cm) sill  plates to slab using approved concrete anchors 

(fasteners not included)

.

 

 

• Check local code for concrete foundation requirements.

NOTES

      Allow new concrete slabs to cure for at least seven (7) days.

2" x 4" x 11'-1-5/8" (5,1 x 10,2 x 339,4 cm)

2" x 4" x 8' (5,1 x 10,2 x 244 cm)

Caulk

Requires:

x2
x2
x1

MUST be treated lumber.

MUST be treated lumber.

96" (243,8 cm)

96" x 140-5/8" (243,8 x 357,2 cm)

133-5/8" (339,4 cm)

8'x 12' (243,8 x 365,8 cm)

140-5/8" (357,2 cm)

A

Actual Size

B

C

Building Size

A

B

C

4"

(10,2 cm)

3-1/2"

(8,9 cm)

DOOR

Treated Sill Plate

Caulk between sill 

plate and concrete.

Summary of Contents for OAKRIDGE 8 x 12

























































































Reviews: