background image

Operator’s Manual

Curved Shaft, 

2-Cycle Trimmer

Model

41AD-280G000

IMPORTANT:

Read safety rules and instructions carefully before operating equipment.

Warning:

This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-

covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting 
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. 
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrestor is installed on this unit. A replacement spark arrestor for the muffler
is available through your nearest engine authorized service dealer or contact the service department, 550 N. 54th Street, Chandler,
Arizona 85226-2434.

MTD SOUTHWEST INC 550 N. 54TH STREET, CHANDLER, ARIZONA 85226-2434

PRINTED IN U.S.A.

FORM NO. 770-10506

PART NO. 10316 rev. A

(12/00)

English

Summary of Contents for 41AD-280G000























Reviews: