background image

Your yard and garden cultivator has been completely
assembled except for the handlebar, throttle cable
and wheel bracket assembly. A large phillips 
screwdriver is needed for assembly.

Removing Unit From Carton

1.

Carefully unpack the contents and insure that 
nothing is damaged. Unwrap the throttle cable 
without bending or kinking it.

WARNING: Do not cut the plastic strap
off the handle bar. The strap is under
tension and can cause serious personal
injury if cut.

2.

Squeeze the handle bar and slide the plastic
strap down and off. See Figure 1.

NOTE: Do not squeeze the handlebar too tight.
Excessive squeezing can cause the handlebar to kink.

5

SECTION 2: ASSEMBLING YOUR CULTIVATOR

SETTING UP YOUR CULTIVATOR

Installing The Wheel Bracket Assembly

WARNING: To avoid injury from the tines,
wear heavy gloves and a long sleeve
shirt when installing the wheel bracket
assembly.

1.

With the unit on it’s side, place the wheel bracket
assembly on the underside of the tine guard. See
Figure 2.

2.

Install a carriage bolt through each of the slotted
holes in the wheel bracket and into the tine
guard.

3.

On the top side of the tine guard, install a lock 
washer and a wing nut onto each of the bolts.
See Figure 2.

4.

Make sure the square shoulder of the bolts are
through the slotted holes in the wheel bracket.
Tighten the wing nuts. See Figure 3.

NOTE: Do not over tighten the wing nuts. Loosening
the wing nuts allow the wheel height to be adjusted.

Figure 1

Figure 2

Figure 3

Squeeze

Together

Plastic

Strap

Wing Nut & 

Lock Washer

Tine

Guard

Wheel

Bracket

Assembly

Summary of Contents for 21A-120R000





















Reviews: