background image

15

SECTION 7: OFF SEASON STORAGE

SECTION 8: TROUBLE SHOOTING GUIDE

If the unit will be stored for an extended time,

1.

Drain all fuel from the fuel tank into a container.
Do not use fuel that has been stored for more
than 60 days. Dispose of the old fuel in 
accordance to local regulations.

2.

Start the engine and allow it to run until it stalls.
This ensures that all fuel has been drained from
the carburetor.

3.

Allow the engine to cool. Remove the spark plug
and put 1 oz. (30 ml) of high quality motor oil 
into the cylinder. Pull the starter rope slowly to 
distribute the oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil
from the cylinder before attempting to start the unit
after storage.

4.

Thoroughly clean the unit and inspect for any
loose or damaged parts. Repair or replace 
damaged parts and tighten loose screws, nuts or
bolts. 

5.

Wipe the tines with an oiled rag to prevent rust.

The unit is ready for storage.

Never store the unit with fuel in the tank where
fumes may reach an open flame or spark.

Allow the engine to cool before storing.

Store the unit in a locked up area to prevent 
unauthorized use or damage.

Store the unit in a dry, well ventilated area. Do not
store next to corrosive materials, such a fertilizer.

Store the unit out of the reach of children.

ENGINE WILL NOT START

ENGINE WILL NOT IDLE

ENGINE WILL NOT
ACCELERATE

ENGINE LACKS POWER
OR STALLS WHEN UNDER
LOAD

On/Off Stop Control in the STOP
position

Empty fuel tank

Primer bulb wasn't pressed enough

Engine flooded

Old or improperly mixed fuel

Fouled spark plug

Air Filter is Plugged

Old or improperly mixed fuel

Improper carburetor adjustment

Old or improperly mixed fuel

Improper carburetor adjustment

Old or improperly mixed fuel

Improper carburetor adjustment

Cultivator tines bound with dirt or
grass

Turn the On/Off Stop Control to START

Fill fuel tank

Press primer bulb fully and slowly 5-7
times

Use starting procedure with choke 
control in the RUN position

Drain fuel tank / Add fresh fuel mixture

Replace or clean the spark plug

Replace or clean the air filter

Drain fuel tank / Add fresh fuel mixture

Refer to MAKING ADJUSTMENTS,
Section 5.

Drain fuel tank / Add fresh fuel mixture

Refer to MAKING ADJUSTMENTS,
Section 5.

Drain fuel tank / Add fresh fuel mixture

Refer to MAKING ADJUSTMENTS,
Section 5.

Stop the unit, switch the On/Off Stop
Control to STOP, clean and remove
any debris binding the tines

Trouble

Possible Cause(s)

Corrective Action

Summary of Contents for 21A-120R000





















Reviews: