background image

12

13

PRODUCT SAFETY WARNINGS

PRODUCT SAFETY WARNINGS

Charger

1.  Recharge only with the charger specified by the 

manufacturer. Do not use the original charger on 
other li-ion batteries or on any other type of battery 
as this can increase the risk of fire or explosion.

2.  Check the battery charger, cable and plug before 

each use. Do not use the battery charger if damaged. 
Do not open the battery charger yourself; charger 
must be repaired by qualified personnel using original 
spare parts.

3.  The charger is designed to use a standard household 

230-240 V~ 50Hz power source, ensure that the plug 
matches the outlet. 

4.  Never modify the plug in any way, this will reduce the 

risk of electric shock.

5.  Do not abuse the cord of charger. Never use the cord 

for carrying, pulling or unplugging the charger. Keep 
cord away from heat, oil, sharp edges or moving 
parts. Damaged or entangled cords increase the risk 
of electric shock.

6.  Make sure the charger cord is situated so that it will 

not be stepped on, tripped over or get damaged.

7.  Keep the battery charger clean. Contamination can 

increase the risk of electric shock.

8.  Protect the battery charger from rain and moisture. 

If water accesses the battery charger there is an 
increased risk of electric shock.

9.  Battery will heat up whilst charging. To reduce the risk 

of fire, do not operate battery charger on flammable 
surfaces such as paper or textiles.

10. The temperature range over which the battery 

pack can be charged is typically between 5ºC-
45 ºC. Attempts to charge out with the prescribed 
temperature range may automatically be blocked by 
the protection circuitry of the battery pack. Longest 
life and best performance can be obtained if the 
battery pack is charged at room temperature.

11. Disconnect charger from the power supply when not 

in use. This will reduce the risk of electric shock or 
damage to the charger.

Battery pack

1.  Fully charge battery pack before first use.
2.  Recharge battery pack immediately when the power 

output starts to slow. DO NOT CONTINUE TO USE 
PRODUCT WHEN BATTERY LEVEL IS LOW.

3.  To prevent serious damage to the battery, charge in 

temperatures above 5ºC or below 45ºC. Longest life 
and best performance can be achieved when battery 
is charged at room temperature.

4.  If the battery temperature is above 45ºC it must be 

allowed to cool before putting it into the charging 
station.

5.  To reduce the risk of explosion, ensure the battery 

pack is not left in the sun for extended periods of 
time and that it is kept away from fire.

6.  Do not carry individual battery packs in your pockets 

or bag as they could short-circuit against other metal 
items.

Summary of Contents for LM T46


















Reviews: