14
15
GB
GB
Maintenance and storage
Maintenance works that have not been instructed within the manual should only be carried out by
a recommended servicing agency. Only use original parts.
Maintenance
Check and clean your Robotic Mower Regularly. Preferably use a dry brush, damp cloth or a
sharpened wooden piece to remove any debris which may be stuck.
Do not clean with a hose or the high pressure water flow from a pressure washer as this may
cause damage. Replace worn parts as necessary.
Winter Storage
During winter, keep your mower, docking station and power supply in a dry place.
We recommend a shed, garage or preferably store it indoors.
Prepare your device for winter storage as follows:
1. Fully recharge the battery.
2. Set the mains power switch to "OFF".
3. Thoroughly clean your Robotic Mower.
4. Unplug the power supply from the mains outlet.
5. Disconnect the power supply from the docking station.
6. Disconnect the boundary wire from the docking station. Lift up the docking station and clean.
The boundary wire can remain outside. However, it is imperative to protect the wire against
corrosion. We recommend a water-free grease or suitable sealing tape.
If available, repack the product in the original packaging.
Alternatively, our service centre offers a winter service for your device. This will include a check-up
of all parts and - if available - a software upgrade.
Preparing for spring
After winter storage, please clean the charging contacts on both the Robotic Mower and the
docking station.
Use a fine abrasion paper or a brass brush; this will help to achieve the best charging efficiency
and avoid any charging interference.
Cleaning the mower body
As your Robotic Mower is battery powered you need take care when cleaning. Remove rough dirt
with a soft brush. Use a manual water spray with mild household detergent for intensive cleaning.
Wipe off any residue after cleaning with a damp cloth.
Disposal
To help the environment, please dispose of the product properly when it has reached the end of
its useful life and not in the household waste. Information on collection points and their opening
hours can be obtained from your local authority.
Li-ion Environmental damage through incorrect disposal of the batteries / rechargeable batteries.
Remove the battery pack from the product before disposal. Batteries /rechargeable batteries may
not be disposed of with the usual domestic waste. They may contain toxic heavy metals and are
subject to hazardous waste treatment rules and regulations. Please dispose of batteries according
to the relevant local requirements.
Cleaning the underside
Ensure the main power switch is in OFF position. Wearing protective gloves, turn the Robotic
Mower onto its side to expose its underside. Clean the blade disc and frame using a soft brush or
damp cloth. Rotate the blade disc to make sure that it can move freely, check that the blades can
turn on their pivots and that there is no grass is obstructing them.
Clean the contact pins and the charging strips
Using wire wool, metal cleaner or very fine grade emery paper, clean the contact pins and the
charging strips on your mower and docking station. Remove any debris, leaves, or grass clippings
around the contact pins and charging strips to ensure efficient charging.
Reversing or replacing the blades
WARNING!
Ensure the Robotic Mower is completely shut off before cleaning, adjusting or replacing
the blades. Always wear protective gloves.
WARNING!
To ensure maximum cutting efficiency and safety, always use recommended replacement
blades and blade mounting parts when replacing.
Your Robotic Mower has three blades, fixed to the blades disk.
Unless damaged by hard obstacles, these blades can last for up to five months of everyday use.
Weekly inspection of the blades and the fixing screws is advised. Note that the blades are double-
edged. When the first side becomes blunt, loosen the fixing screw and the blade upside down and
re-fix. Check that the blade can move freely.
A set of spare blades is included with the Robotic Mower. More blades can be purchased via our
customer support team or our website www.yardforce.eu.
To ensure you get the best performance from your machine, always replace all three blades at the
same time. Only use spare parts recommended by manufacturer.
Spare parts list
Call the customer support team if you want to order below spare parts.
Boundary pegs Spare blades Boundary wire connectors Boundary wire
Software Update
Should your machine need a software update, contact our customer support team for more
information.
O
OFFFF
00
11
O
ONN
