background image

 

 

12

 

 

 

 

Warranty 

For one year from the date of purchase YTL International will replace for the original purchaser, or repair the 

push spreader.    The warranty will not apply to any unit which was not assembled correctly, misused, 

overloaded or which has been used or operated contrary to our instructions, or which has been repaired or 

altered by anyone other than an authorized representative.   

 

Warranty Exclusions 

This warranty does not cover cosmetic defects such as paint, decals or wear items such as tires.    This 

warranty will not cover failures or problems due to acts of God, or events or forces beyond the control of the 

manufacturer.    

 

 

Normal Wear Exclusion 

The spreader needs periodic service to perform well. This warranty does not cover repair when normal use has 

exhausted the life of a part or the equipment as a whole. 

 

Installation, Use and Maintenance Exclusion 

This warranty will not apply to parts and/or labor if the push spreader has been misused, neglected, involved in 

an accident, abused, loaded beyond its limits, modified or assembled incorrectly.    Normal maintenance is not 

covered under this warranty. 

 

Limits of Implied Warranty and Consequential Damage Exclusion 

YTL International disclaims any obligation to cover any loss of time, use of this product, freight, or any 

incidental or consequential claim by anyone from using this push spreader. THIS WARRANTY IS IN LIEU OF 

ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY 

OR FITNESS FOR A PARTICULAR. 

 

An exchange unit will be subject to the original warranty. The length of the warranty governing the exchanged 

unit will have the date as the purchase date of the original unit. This warranty gives you certain legal rights 

which may change from state to state. Your state may also have other rights you may be entitled to that are not 

listed within this warranty. 

 

Contact Information 

YTL International 

17517 Fabrica Way, Suite H 

Cerritos, CA  90703 

Phone: (888) 723-6534 

Phone: (562) 404-8016 

Fax: (562) 404-8013 

 

Limited Warranty

Summary of Contents for YTL31507













Reviews: