background image

Control Panel

(1)

(2)

(3)

(4)

(5)

(6)

(7)

0004614

Figure 9

1 – Insufficient Engine Speed Warning Indicator

2 – Power Box is Running Indicator

3 – Power Box Temperature Warning Indicator

4 – Generator Temperature Warning Indicator

5 – Power Box ON / OFF Switch

6 – Overload Warning Indicator

7 – Fuse
• Insufficient Engine Speed Warning Indicator (Figure 9, (1)): A red LED that illuminates

when engine speed is too low for the load.

• Power Box is Running Indicator (Figure 9, (2)): A green LED that illuminates when the

power box main switch is ON.

• Power Box Temperature Warning Indicator (Figure 9, (3)): A red LED that illuminates

when the power box (inverter) temperature is too high.

• Generator Temperature Warning Indicator (Figure 9, (4)): A red LED that illuminates when

the generator temperature is too high.

• Power Box ON / OFF Switch (Figure 9, (5)): ON / OFF switch for the power box.
• Overload Warning Indicator (Figure 9, (6)): Two red LEDs illuminate when the Insufficient

Engine Speed Warning and the Power Box Temperature Warning Indicators are lit.

• Fuse (Figure 9, (7)): For 12V DC Line
See Checks During Operation on page 26 for operation information.

PRODUCT OVERVIEW

20

KMG65E Operation Manual

Summary of Contents for KMG Series















































Reviews: