manualshive.com logo in svg

Yanmar 4JH4-TE, Operation Manual

Share
Download
Yanmar 4JH4-TE Operation Manual Download Page 19

2. PRODUCT EXPLANATION

              15

(3) Alarm Equipment (Lamps and Buzzer)

When the sensor detects a problem during operation, the lamp comes on and the buzzer sounds.
Alarm lamps are located on the panel, buzzer is located on the back of panel. 
Under normal conditions, the monitors are off. When there is a problem, the monitors light up.

(4) Normal Action of Alarm Devices

Alarm devices act as shown below.
Please check that the alarm lamps and buzzer are working normally, when the key is turned on.

Battery low 
charge alarm

When the alternator output is too low, the lamp will come on.
When charge begins, the lamp will turn off.
(The alarm buzzer will not sound, when the lamp comes on.)

Coolant high 
temperature 
alarm

When the temperature reaches the maximum (95°C[203°F] or higher), the lamp will 
light and the alarm will sound. 
Continuing operation at temperatures exceeding the maximum limit will result in dam-
age and seizure. 
Check the load and the fresh water cooling system for any abnormalities.

Lube oil low 
pressure alarm

When the lube oil pressure falls below normal, the oil pressure sensor will register 
this and the lamp will come on and alarm will sound. 
Continuing operation with insufficient oil pressure will result in damage and seizure. 
Check the oil level.

Water in sail 
drive seal alarm

When sea water is detected between the seals of sail drive, the lamp will come on 
and alarm will sound.

Water in fuel 
filter alarm
(C type only)

When the drain inside the water separator in the fuel filter becomes excessive, the 
sensor will cause the lamp to come on.

Sea water 
insufficient flow 
alarm
(C type only)

This function is not available on this engine.

Key switch

OFF 

→ 

ON

START 

→ 

ON

Engine

Before start

Running

Alarm buzzer

Sound

Stop

Alarm lamps

Battery low charge alarm

Light

Off

Coolant high temperature alarm

Off

Off

Lube oil low pressure alarm

Light

Off

Water in sail drive seal alarm

Off

Off

Summary of Contents for 4JH4-TE







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands