Yanmar 0A2V000-U0000 Operation Manual Download Page 54 | Manualshive

Page: 54 / 112

background image

BEFORE YOU OPERATE

38

2V Operation Manual

Engine Oil Capacity

The following are engine oil capacities for 2V750V
engine.

Note: These are the engine oil capacities

associated with a “Standard” oil pan. Oil
capacity will vary depending upon which
optional oil pan is used. Refer to the
operation manual provided by the driven
machine manufacturer for the actual
engine oil capacity of your machine.

ENGINE COOLANT

Engine Model

Dipstick Upper

Limit / Lower Limit

2V750V

2.40 / 1.39 qt

(2.27 / 1.31 L)

A

DANGER

SCALD HAZARD!

• NEVER remove the radiator cap if the

engine is hot. Steam and hot engine
coolant will spurt out and seriously
burn you. Allow the engine to cool
down before you attempt to remove
the radiator cap.

• Securely tighten the radiator cap after

you check the radiator. Steam can
spurt out during engine operation if
the cap is loose.

• ALWAYS check the level of the engine

coolant by observing the reserve tank.

• Failure to comply will result in death or

serious injury.

0000002en

A

WARNING

BURN HAZARD!

• Wait until the engine cools before you

drain the engine coolant. Hot engine
coolant may splash and burn you.

• Failure to comply could result in death

or serious injury.

0000016en

A

CAUTION

COOLANT HAZARD!

• Wear eye protection and rubber gloves

when you handle Long Life or
Extended Life engine coolant. If
contact with the eyes or skin should
occur, flush eyes and wash
immediately with clean water.

• Failure to comply may result in minor

or moderate injury.

0000005en

«
...
52
53
54
55
56
...
»

Summary of Contents for 0A2V000-U0000

















































































































Reviews:

No comments

Related manuals for 0A2V000-U0000

Brand: Rail King Pages: 46

Brand: Indmar Pages: 94

Brand: Grundfos Pages: 25

Brand: Ofna Racing Pages: 2

AstroTrack 21047

Brand: ORION TELESCOPES & BINOCULARS Pages: 2

Brand: Daedong Pages: 66

Brand: Lenze Pages: 36

MCA10I40 Series

Brand: Lenze Pages: 44

Smart Motor m300

Brand: Lenze Pages: 116

Brand: Lenze Pages: 72

Brand: DJ ENGINE Pages: 9

Brand: O.S. engine Pages: 16

Brand: O.S. engine Pages: 46

Brand: HAMPTON BAY Pages: 17

Brand: YS Pages: 2

BREVINI T Series

Brand: DANA Pages: 46

BREVINI E 100 Series

Brand: DANA Pages: 50

Brand: Hydro-Gear Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands