manualshive.com logo in svg

Yampp 3U, Reference Manual, Page: 8 / 17

Share
Download
Yampp 3U Reference Manual Download Page 8

Yampp-3U 

 

Reference Manual

 

Contents 

 

Version 1.10, 

11/10/2005 

 

Page 8 of 13 

4 LCD 

Assembly 

 

Several types of LCD can be installed on the Yampp-3U player. Here is the instruction to install a 

character LCD module and the Nokia graphic LCD. 

4.1  Character LCD Installation 

 

It’s possible to install different kind and size of character display module. Actually, Yampp-3U can 

support 2x16, 2x20, 2x24, 2x40, 4x16 and 4x20 characters displays. You must edit the 

“constant.h” in the firmware package to define the display that will be use and you must rebuild 

and update the firmware. The procedure of updating the firmware is explained in section 8.1. 
 

The next table shows you how to connect the character LCD module. The pinout of the LCD 

module can be different from a model to another one. So it is very important to check the LCD 

datasheet for the correct pinout. 

 

 

 

Ke Display

J2

8

6

4

2

7

5

3

1

AD2

AD3

AD4

AD6

KEYS

AD5

AD7

TX_EN

9

11

13

15

16

14

12

10

GND

V0 (VEE)

A1 (R/W)

AD0

AD1

LCD_E (E)

A0 (RS)

VCC

 

 

 

Summary of Contents for 3U


















Reviews:

No comments