Yamato Pure Line WL220T Instruction Manual Download Page 17

Page: 17 / 44

3. Names and Functions of Parts

Piping diagram

1. Water supply hose

6. Water quality sensor

2. Reducing valve

7. Tank

3. Water supply solenoid valve

8. Air filter

4. Ion exchange resin cartridge (CPC-P)

9. Cock

5. Ion exchange resin cartridge (CPC-E)

10. Drain cock

※

The reducing valve pressure has been set to 0.4

100kPa(raw water pressure

：

100kPa)

at the factory.

Remote water supply input terminal (optional)

1. Water supply hose

7. Tank

2. Reducing valve

8. Air filter

3. Water supply solenoid valve

9. Cock

4. Ion exchange resin cartridge (CPC-P)

10. Drain cock

5. Ion exchange resin cartridge (CPC-E)

11. Water supply solenoid valve (optional)

6. Water quality sensor

※

The reducing valve pressure has been set to 0.4

100kPa(raw water pressure

：

100kPa)

at the factory.

②

③

④

⑤

⑥

⑦

⑩

⑧

⑨

②

③

④

⑤

⑥

⑦

⑨

⑧

⑩

⑪

Optional

①

o
con

ant

temp.

humi

chamb

ap
w

er
m

val
ve

①

const

temp.

umi

chamb

ap
w

er
m

val
ve

Summary of Contents for Pure Line WL220T













































Search results

Summary of Contents for Pure Line WL220T

Reviews:

Related manuals for Pure Line WL220T

Brands by name

Popular brands

Yamato Pure Line WL220T, Instruction Manual

Search results

Summary of Contents for Pure Line WL220T

Reviews:

Related manuals for Pure Line WL220T

Brands by name

Popular brands