Yamato IN604W Instruction Manual Download Page 58

Page: 58 / 66

In the Event of Failure…

Error Indication

Error code

Name

Cause

Solution

Er.00

Setting value

error

Setting value is out of usable range

Set correct value.

Er.01

Sensor error

Temperature sensor failure

Contact to our service division.

Er.02

SSR error

SSR failure

Contact to our service division.

Er.03

Heater error

Heater disconnection
(Detection is available only during
the heater is controlled.)

Contact to our service division.

Er.07

Independent

overheating

prevention

device activation

Independent overheating prevention
device is in operation

Reset the power supply, and
then

adjust

the

setting

temperature of the independent
overheating prevention device.

Er.10

Main relay error

Contact to our service division.

Er.13

Refrigerator error Overload of refrigerator

Contact to our service division.

Er.14

RAM error

Checksum abnormality in RAM

Contact to our service division.

Er.15

EEPROM error

Checksum abnormality in EEPROM Contact to our service division.

Summary of Contents for IN604W



































































Search results

Summary of Contents for IN604W

Reviews:

Yamato IN604W, Instruction Manual, Page: 58 / 66

Search results

Summary of Contents for IN604W

Reviews: