Yamato IN604W Instruction Manual Download Page 27 | Manualshive

Page: 27 / 66

Yamato IN604W Instruction Manual Download Page 27

24

Operation Method

Program Operation

4

Start operation

①

Press the ENTER key to decide the operation

start  wait  period/time.    The  unit  enters  to
program  operation  wait  state.    The  blinking
PROGRAM  lamp  lights  on  and  the  STANDBY
lamp  blinks  instead  in  this  state.    The  Sub
Display  displays  the  step  number  and  residual
time to operation start.

②

The operation starts when the residual time

counts  zero.    The  STANDBY  lamp  lights  off  and
the  Sub  Display  displays  the  executing  step
number  and  the  setting  temperature  after  the
operation starts.

③

The following screens are displayed in sequence

during operation.

Set TEMP

37.0

℃↑

Step

S01

(Executing step number)

↓

Set TEMP

37.0

℃↑

Remain

15min

(Remaining time)

↓

Set TEMP

37.0

℃↑

Rep. count

10

(Residual count of repeat:

displayed during repeat only)

↓

Set TEMP

37.0

℃↑

Wait

5min

(Waiting state: displayed

during wait only)

④

The END lamp blinks and the Sub Display

displays the operation finish time when the
operation stops.

⑤

Press the POWER key to cancel the operation or

quit the wait state.

«
...
25
26
27
28
29
...
»

Summary of Contents for IN604W



































































Reviews:

No comments