Yamato DPI-500 Technical Manual Download

Page: 14 / 15

DPI-500

Technical Manual

User Keyword Descriptions:

Appendix B: Error Codes

Keyword

Baud Rate

Data Bits and Parity

Serial Transmission
Mode

Display Check

Disable the lb/kg
Key

Serial Port Mode

ID No. Enable

ID No. Entry

No. of Line
Feeds

Description

Select the baud rate for transmission through the serial port.

Selects number of data bits and parity for serial port transmission.

Selects the type of serial mode transmission.
"C" = Continuous mode; Send data continuously.
"d" = Demand mode; Send data on PRINT command from computer, printer, indicator.

Actuates the function which checks all display digits.

Allows user to disable the lb/kg key.
"0" = disable
"1" = enable

Selects the mode of the RS-232C serial port.
"0" = full duplex mode
"1" = Gross/Net/Tare print mode

Allows the ID No. to be disabled in the Gross/Net/Tare printout. Valid only when

is set to "1".

"0" = disable
"1" = enable

Actuates the function which allows the entry of a new ID No. Valid only when

is set to "1".

Pressing the

ZERO

key to scroll down once starts the sequence.

Actuates the function which allows entry of the desired number of line feeds to be printed after the
Gross/Net/Tare printout. Valid only when

is set to "1". Pressing the

ZERO

key to scroll

down once starts the sequence.

Value

1200

2400

4800

9600

Press ZERO key to
begin sequence

- 199999

- 99

Error

Err 0

Err 1

Err 2

Err 3

Err 4

Err 5

Err 7

Err 9

Where it Occurs

Normal Weighing Mode

Span Calibration Mode (F17)

All Modes

Key-in Span Calibration Mode
(F20)

Initialization

Normal Weighing Mode

Meaning

Gross overload.

Keyed-in weight value in Calibration Procedure is less than 1% of full scale capacity.

Keyed-in weight value in Calibration Procedure is larger than full scale capacity.

Internal resolution is not high enough to process keyed-in weight value in Calibration
Procedure.

Diagnostics check error - EEPROM Read

Diagnostics check error - EEPROM Write

Attempted to key-in zero for C1.

No reading from analog to digital converter.

Span calibration lost.

Summary of Contents for DPI-500
















Search results

Summary of Contents for DPI-500

Reviews:

Related manuals for DPI-500

Brands by name

Popular brands

Yamato DPI-500, Technical Manual

Search results

Summary of Contents for DPI-500

Reviews:

Related manuals for DPI-500

Brands by name

Popular brands