Yamato CD 12 L, Instruction Manual

Page: 15 / 31

15
TECHNICAL DATA
Model CD 12 L CD 16 L CDP 16 L CDP 20 L
Code 99360 99361 99362 99363
Voltage 12 volt 16 volt 16 volt 20 volt
Battery Type Li-ion Li-ion Li-ion Li-ion
Battery Capacity 1,5 Ah 2,0 Ah 2,0 Ah 2,0 Ah
Charger voltage
230V-50Hz 230V-50Hz 230V-50Hz 230V-50Hz
Speed
2 2 2 2
No Load speed (rpm)
0~350/0~1350 0~350/0~1250 0~350 / 0~1250 0~350 / 0~1250
Impact rate (bpm) - - 0~5250/0~18750 0~5250/0~18750
Torque settings 18 + 1 19 + 1 16 16
Max Torque 20 Nm 28 Nm 33 Nm 35 Nm
Chuck
10 mm 10 mm 13 mm 13 mm
Impact
NO NO YES YES
Second battery
NO NO YES YES
Charging time
1 h 1 h 1 h 1 h
Sound pressure level (L
pA
)
dB(A)
68,2 dB(A)
K
pA
=3 dB(A)
84 dB(A)
K
pA
=3 dB(A)
84 dB(A)
K
pA
=3 dB(A)
84 dB(A)
K
pA
=3 dB(A)
Sound power level (L
WA
)
dB(A)
79,2 dB(A)
K
WA
=3 dB(A)
95 dB(A)
K
WA
=3 dB(A)
95 dB(A)
K
WA
=3 dB(A)
95 dB(A)
K
WA
=3 dB(A)
Vibration level
Drilling
1,552 m/s
2
K=1,5 m/s
2
1,552 m/s
2
K=1,5 m/s
2
1,552 m/s
2
K=1,5 m/s
2
1,552 m/s
2
K=1,5 m/s
2
Vibration level
Impact drilling
- -
7,528 m/s
2
K=1,5 m/s
2
7,528 m/s
2
K=1,5 m/s
2
CHARGING PROCEDURE
NOTE
: Before using the tool, read the instruction book carefully.
1. RECHARGING BATTERIES
A) CHARGING THE BATTERY
The battery charger supplied is matched to the Li-ion battery installed in
the machine. Do not use another battery charger. The Li-ion battery is protected against deep
discharging. When the battery is empty, the machine is switched off by means of a protective
circuit: The chuck no longer rotates. In a warm environment or after heavy use, the battery pack
may become too hot. Allow time for the battery to cool down before recharging. When the
battery pack is charged for the first time and after prolonged storage, the battery will only accept
approximately 60% charge. However, after several charge and discharge cycles the battery will
accept a 100% charge.
B) IMPORTANT NOTES FOR CHARGING THE BATTERY The battery in your new tool is not charged when
it leaves the plant. Therefore it must be charged for 1 hour before using the first time!
C) CHARGING Plug the charger plug into a suitable mains socket, and the indicator light will shoe
green. Then insert the battery pack into the charger, the indicator light will become red to indicate
thet charging is taking place.
The three green intelligent battery indicators will continue
flashing when start charging. Two indicators will flash inturn
when the capacity reach 70%. One indicator light flash when
100% charged. Three indicators will keep light when finished
charging. After a few seconds, the indicators will off.
After charging 1 hour, the battery will be fully charged, the
light will turn to green. Unplug the charger plug from the wall
socket, the tool is ready to use.