Yamato BS 200 Instruction Manual Download Page 9

 

 

 

 

Before Using this unit 

Requirements for Installation 

 

CAUTION! 

 

6. Choose a correct power distribution board or receptacle

 

 

  Choose a correct power distribution board or receptacle that meets the unit

’s rated electric 

capacity. 

Electric capacity: 

BS200:    220V AC, 4.5A 
BS400:    220V AC, 6.5A 
BS600:    220V AC, 6.5A 
BS660:    220V AC, 6A

 

  If  the  power  supply  voltage  is  lower  than  the  required  voltage,  the  capacity  of  the  heater  may 

decrease,  the  temperature  of  the  water  may  not  rise  with  enough,  or  the  temperature  controller 
may cause to be malfunction.    Check whether the power line shares  with other device(s) or not.   
If does so, isolate the power line of this device from that (those) of other device(s). 

 

7. Before/after installing 

 

  It may cause injure to a person if this unit falls down or moves by the earthquake and the 

impact etc..To prevent, take measures that the unit cannot fall down, and not install to busy 
place. 

  Touching the unit may cause a burn during and just after the operation. To prevent, take 

measures that putting up a notice of operating etc.. 

 

8. Handling of power code

 

 

  Do not entangle the power cord. This will cause overheating and possibly a fire. 

  Do not bend or twist the power cord, or apply excessive tension to it. This may cause a fire 

and electrical shock. 

  Do not lay the power cord under a desk or chair, and do not allow it to be pinched in order to 

prevent it from being damaged and to avoid a fire or electrical shock. 

  Keep the power cord away from any heating equipment such as a room heater. The cord's 

insulation may melt and cause a fire or electrical shock. 

 

  If the power cord becomes damaged (wiring exposed, breakage, etc.), immediately turn off the 

power at the rear of this unit and shut off the main supply power. Then contact your nearest 
dealer for replacement of the power cord. Leaving it may cause a fire or electrical shock. 

  Connect the power plug to the receptacle which is supplied appropriate power and voltage. 

 

9. Thermometer installation 

 

  Thermometer has line marking of im mersion level at around 76mm from iower end of   

Thermometer. Im merse thermometer under water up to the im mersion level to read   
Temperature properly. 

 
 

Summary of Contents for BS 200

























Reviews: