Yamatake-Honeywell 7800 Series, Product Data

Page: 4 / 32

7800 SERIES EC7885A/RM7885A RELAY MODULE
65-0203 4
Table 2. Flame Detection Systems.
Plug-in Flame Signal Amplifiers Applicable Flame Detectors
Type Color
Self-
Checking Model
Flame Failure
Response Time Fuel Type Models
Rectification Green No R7847A .8 or 3 sec Gas Rectifying
Flame Rod
Holders
a
C7004, C7007, C7011.
Complete Assemblies:
C7008, C7009, Q179.
No R7847A .8 or 3 sec Oil Rectifying
Photocell
e
C7003, C7010, C7013,
C7014.
e
No R7847A 3 sec Gas, oil, coal Ultraviolet
(Purple
Peeper)
C7012A,C.
b
Dynamic
AMPLI-
CHECK® R7847B
c
.8 or 3 sec Gas Rectifying
Flame Rod
Holders
a
C7004, C7007, C7011.
Complete Assemblies:
C7008, C7009, Q179.
Dynamic
AMPLI-
CHECK® R7847B
c
.8 or 3 sec Oil Rectifying
Photocell C7003, C7010, C7013,
C7014.
e
Dynamic
AMPLI-
CHECK®
f
R7847B
c
3 sec Gas, oil, coal Ultraviolet
(Purple
Peeper)
C7012A,C.
b
Dynamic
Self -
Check
f
R7847C
d,f
3 sec Gas, oil, coal Ultraviolet
(Purple
Peeper)
C7012E,F.
Infrared Red No R7848A 3 sec Gas, oil, coal Infrared
(Lead Sulfide)
C7015.
Dynamic
AMPLI-
CHECK® R7848B
c
3 sec Gas, oil coal Infrared
(Lead Sulfide) C7015.
Ultraviolet Purple No R7849A .8 or 3 sec Gas, oil Ultraviolet
(Minipeeper) C7027, C7035,
C7044.
b
Dynamic
AMPLI-
CHECK® R7849B
c
.8 or 3 sec Gas, oil Ultraviolet
(Minipeeper) C7027, C7035,
C7044.
b
Purple Dynamic
Self -
Check
f
R7861A .8 sec Gas, oil, coal Ultraviolet C7061.
Blue Dynamic
Self -
Check
f
R7886A
d
3 sec Gas, oil, coal Ultraviolet
(Adjustable
Sensitivity)
C7076.
a
Order flame rod separately; see holder Instructions.
b
The C7012A,C, C7027, C7035 and C7044 Flame Detectors should be used only on burners that cycle on-off at least once
every twenty-four hours. Appliances with burners that remain on continuously for twenty-four hours or longer should use
the C7012E,F Flame Detector with the R7847C Amplifier or the C7076A,D Flame Detector with the R7886A Amplifier or
the C7061 Flame Detector with the R7861 Amplifier as the ultraviolet flame detection system.
c
Circuitry tests the flame signal amplifier at least 12 times a minute during burner operation and shuts down the burner if the
amplifier fails.
d
Circuitry tests all electronic components in the flame detection system (amplifier and detector) 12 times a minute during
burner operation and shuts down the burner if the detection system fails.
e
Use only Honeywell Photocell, part no. 38316, ONLY.
f
Requires the use of a separate step down transformer when used with the EC7885A. See figure 16.