manualshive.com logo in svg

Yamaha Z250D, Owner'S Manual

Share
Download
Yamaha Z250D Owner'S Manual Download Page 76

 

Trouble Recovery

 

71

 

EMU29471

 

Replacing fuse

 

If a fuse has blown, remove the electrical
cover, open the fuse holder and remove the
fuse with a fuse puller (if equipped). Replace
it with a spare one of the proper amperage.

WARNING

 

EWM00630 

 

Be sure to use the specified fuse. An in-
correct fuse or a piece of wire could allow
excessive current flow. This could cause

 

electric system damage and a fire hazard.

NOTE:

 

Consult your Yamaha dealer if the new fuse

 

immediately blows again.

 

EMU29520

 

Power trim and tilt will not operate

 

If the engine cannot be tilted up or down with
the power trim and tilt/ the power tilt because
of a discharged battery or a failure with the
power trim and tilt unit/the power tilt, the en-
gine can be tilted manually.
1.

Loosen the manual valve screw by turn-
ing it counterclockwise until it stops.

2.

Put the engine in the desired position,
then tighten the manual valve screw by
turning it clockwise.

 

1. Electrical cover
2. Fuse holder
3. Fuse (20 A, 30 A, 100A)
4. Spare fuse (20 A, 30A, 100A)
5. Fuse puller

3

5

4

1

3

4

3

2

ZMU01903

 

1. Fuse (20 A, 30 A, 100A)
2. Fuse puller

1. Manual valve screw

1

2

ZMU01904

1

ZMU01905

Summary of Contents for Z250D
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands