Yamaha YZFR6W Owner'S Manual Download Page 61

Page: 61 / 118

PERIODIC MAINTENANCE AND MINOR REPAIR

6-11

To install the cowling

1. Place the cowling in the original

position, and then install the bolts,
quick fasteners, and quick fastener
screw.

2. Connect the turn signal light lead

coupler.

3. Install cowling A (to complete the

installation of cowling C) or cowl-
ing B (to complete the installation
of cowling D).

EAU39091

Cowling E

To remove the cowling

1. Remove cowling B and panel B.

(See page 6-9.)

2. Unfasten the wire harness by

pressing on the tab to open the
plastic fastener.

3. Remove the bolts and the quick

fastener, and then pull the cowling
off as shown.

1. Cowling D
2. Bolt

3. Turn signal light lead coupler

4. Quick fastener

1. Quick fastener

1. Quick fastener screw

1. Plastic fastener
2. Tab

3. Wire harness

U2C011E0.book Page 11 Wednesday, July 12, 2006 10:13 AM

Summary of Contents for YZFR6W























































































































Search results

Summary of Contents for YZFR6W

Reviews:

Related manuals for YZFR6W

Brands by name

Popular brands

Yamaha YZFR6W, Owner'S Manual

Search results

Summary of Contents for YZFR6W

Reviews:

Related manuals for YZFR6W

Brands by name

Popular brands