Yamaha YZFR6W Owner'S Manual Download Page 42

Page: 42 / 118

INSTRUMENT AND CONTROL FUNCTIONS

3-24

EAU15311

Ignition circuit cut-off system

The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.

●

It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.

●

It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.

●

It cuts the running engine when the
transmission is in gear and the sid-
estand is moved down.

Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.

WARNING

EWA10250

If a malfunction is noted, have a
Yamaha dealer check the system be-
fore riding.

U2C011E0.book Page 24 Wednesday, July 12, 2006 10:13 AM

Summary of Contents for YZFR6W























































































































Search results

Summary of Contents for YZFR6W

Reviews:

Brands by name

Popular brands

Yamaha YZFR6W, Owner'S Manual

Search results

Summary of Contents for YZFR6W

Reviews:

Brands by name

Popular brands