manualshive.com logo in svg

Yamaha YZ450F(E) 2014, Owner'S Service Manual

The Yamaha YZ450F(E) 2014 Owner's Service Manual is a comprehensive guide for owners of the powerful off-road motorcycle. This essential manual provides detailed instructions on maintenance, troubleshooting, and repair procedures, ensuring optimal performance. Download this manual for free from our trusted website, making it easily accessible to all Yamaha enthusiasts.

Share
Download
background image

CRANKSHAFT ASSEMBLY AND BALANCER SHAFT

5-69

4. Check:

• Crankshaft sprocket “1”

Damage 

 Replace the crankshaft.

5. Check:

• Crankshaft journal oil passage

Obstruction 

 Blow out with compressed 

air.

EAS1SL1287

INSTALLING THE CRANKSHAFT ASSEM-
BLY

1. Install:

• Crankshaft assembly

TIP

Install the crankshaft assembly with the crank-
shaft installer pot “1”, crankshaft installer bolt 
“2”, adapter (M12) “3” and spacer “4”.

ECA13970

NOTICE

• To avoid scratching the crankshaft and to 

ease the installation procedure, lubricate 
the oil seal lips with lithium-soap-based 
grease.

• In order to prevent the crankshaft seizure, 

apply molybdenum disulfide grease.

TIP

Hold the connecting rod at top dead center 
(TDC) with one hand while turning the nut of the 
crankshaft installer bolt with the other. Turn the 
crankshaft installer bolt until the crankshaft as-
sembly bottoms against the bearing.

Crankshaft installer pot

90890-01274

Installing pot

YU-90058

Crankshaft installer bolt

90890-01275

Bolts

YU-90060

Adapter (M12)

90890-01278

Adapter #3

YU-90063

Spacer (crankshaft installer)

90890-04081

Pot spacer

YM-91044

1

Summary of Contents for YZ450F(E) 2014









































































































































































































































































































































































Reviews:

No comments

Related manuals for YZ450F(E) 2014

Honda 1989 CBR1000F Owner'S Manual preview
1989 CBR1000F
Brand: Honda Pages: 104
APRILIA SHIVER 750 - Brochure preview
SHIVER 750 -
Brand: APRILIA Pages: 9
LedGlow Advanced Million Color Mini Motorcycle Lighting Kit Installation Instructions preview
Advanced Million Color Mini Motorcycle Lighting Kit
Brand: LedGlow Pages: 3
hepco & becker 6504513 01 01 Manual preview
6504513 01 01
Brand: hepco & becker Pages: 4
Suzuki 990D0-28K50-CLE Installation Instructions Manual preview
990D0-28K50-CLE
Brand: Suzuki Pages: 12
KTM 525 XC Owner'S Manual preview
525 XC
Brand: KTM Pages: 207
Yamaha SXV70G 2001 Service Manual preview
SXV70G 2001
Brand: Yamaha Pages: 172
Yamaha T115FL-2P Owner'S Manual preview
T115FL-2P
Brand: Yamaha Pages: 80
Hudora 84201-03 Instructions On Assembly And Use preview
84201-03
Brand: Hudora Pages: 8
Yamaha 1990 FZR1000 Assembly Manual preview
1990 FZR1000
Brand: Yamaha Pages: 5
Yamaha 1985 XV700 Virago Manual preview
1985 XV700 Virago
Brand: Yamaha Pages: 10
Yamaha 1987 FZR1000 Service Information preview
1987 FZR1000
Brand: Yamaha Pages: 65
Yamaha 1991 XV250B Owner'S Manual preview
1991 XV250B
Brand: Yamaha Pages: 100
Yamaha 1990 XV250A Owner'S Manual preview
1990 XV250A
Brand: Yamaha Pages: 100
Yamaha 1991 XV1000B Owner'S Manual preview
1991 XV1000B
Brand: Yamaha Pages: 108
Yamaha 1989 XV1000 Owner'S Manual preview
1989 XV1000
Brand: Yamaha Pages: 100
Yamaha 135LC 2022 Owner'S Manual preview
135LC 2022
Brand: Yamaha Pages: 88
Yamaha 1969 F5 Service Manual preview
1969 F5
Brand: Yamaha Pages: 94

Brands by name

Popular brands

Load more brands