background image

3-25

ELECTRICAL

TROUBLESHOOTING

The following guide for troubleshooting does not cover all the possible causes of problems. If the following problems occur, 
perform the specified checks or maintenance jobs. If a problem occurs that is not listed in this manual or if the problem 
cannot be corrected by the procedures provided in this manual, contact your Yamaha dealer.

Engine starting problems, engine idling speed problems, and medium and high-speed performance problems

• Engine does not start even though the kickstarter is pushed.
• Engine starts, but soon stops.

Engine idling speed problems

• Engine idling speed fluctuates.
• Engine idling speed is high.
• Engine idling speed is low.

Medium and high-speed performance problems

• Engine speed does not increase.
• Engine knocks.
• Engine speed increases suddenly.
• Loss of engine power.

INSPECTION STEPS

If the aforementioned problems have occurred, perform the following inspection steps in the order given.

Check that the fuel tank is filled with fresh gaso-
line.

No good

Fill the fuel tank.

OK

Check that the fuel tank breather hose is not 
clogged. (Refer to "INCLUDED PARTS" section 
in the CHAPTER 1.)

No good

Repair or replace.

OK

Adjusting the engine idling speed(Refer to "AD-
JUSTING THE ENGINE IDLLING SPEED" sec-
tion in the CHAPTER 3.)

No good

Adjust.

OK

Check that the fuel hose is connected properly 
and is not kinked or pinched.

No good

Repair.

OK

Check the spark plug for dirt, the spark plug gap, 
and the spark plug cap. (Refer to "CHECKING 
THE SPARK PLUG" section in the CHAPTER 3.)

No good

Clean or adjust.

OK

Check that the air filter element is installed cor-
rectly and is not clogged. (Refer to "CLEANING 
THE AIR FILTER" section in the CHAPTER 3.)

No good

Clean or repair.

OK

Checking the sensors, injector and ignition coil 
connection.

No good

Repair or replace.

OK

Installed condition of ECU (Refer to "CHECKING 
THE ECU" section in the CHAPTER 7.)

No good

Repair.

OK

Check the assembled condition of the throttle 
body, and check the throttle valve and its sur-
rounding parts for dirt.

No good

Repair or clean.

OK

Consult a Yamaha dealer.

Summary of Contents for YZ450F(B) 2012





































































































































































































































Reviews: