Yamaha YXZ 1000RSS Owner'S Manual Download Page 67

Page: 67 / 220

4-39

3. Tighten the locknut to the specified

torque.

NOTICE:

Always tighten the

locknut against the adjusting nut, and
then tighten it to the specified torque.

[ECB00082]

1. Distance B
2. Crossover locknut
3. Crossover adjusting nut

Crossover setting:

Minimum (soft):

Distance B = 47.6 mm (1.88 in)

Standard (recommended):

Distance B = 60.3 mm (2.38 in)

Maximum (hard):

Distance B = 73.0 mm (2.88 in)

(b)

(a)

Tightening torque:

Locknut:

41 N·m (4.1 kgf·m, 30 lb·ft)

1. Special tool
2. Torque wrench
3. Crossover locknut

90˚

UB0F10E0.book Page 39 Friday, October 27, 2017 2:03 PM

Summary of Contents for YXZ 1000RSS





























































































































































































































Search results

Summary of Contents for YXZ 1000RSS

Reviews:

Related manuals for YXZ 1000RSS

Brands by name

Popular brands

Yamaha YXZ 1000RSS, Owner'S Manual

Search results

Summary of Contents for YXZ 1000RSS

Reviews:

Related manuals for YXZ 1000RSS

Brands by name

Popular brands