Yamaha YP125R Service Manual Download | Manualshive

Page: 387 / 498

background image

FUEL TANK

7-4

c. Start the engine.
d. Measure the fuel pressure.

Faulty

→

Replace the fuel tank (with fuel

pump).

e. Connect the fuel hose and install the fuel

hose connector cover.
Refer to “INSTALLING THE FUEL TANK” on
page 7-4.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS37P1072

INSTALLING THE FUEL TANK

1. Install:

• Gasket
• Fuel sender “1”

TIP

Install the fuel sender with the fuel sender
wrench “2”.

2. Install:

• Fuel hose
• Fuel hose connector cover

NOTICE

ECA37P1022

When installing the fuel hose, make sure that
it is securely connected, and that the fuel
hose connector cover is in the correct posi-
tion, otherwise the fuel hose will not be prop-
erly installed.

TIP

• Wipe up any fuel remaining in the recess “a” in

the fuel pump with a dry rag “1”.

• After installing the fuel hose connector cover

“2”, make sure that it is installed securely.

Pressure gauge

90890-03153
YU-03153

Fuel pressure adapter

90890-03181

Output pressure

250.0 kPa (2.50 kgf/cm², 36.3
psi)

Fuel sender wrench

90890-11098

3

4

2

New

2

1

a

1

2

«
...
385
386
387
388
389
...
»

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YP125R

Brand: RACCEWAY Pages: 53

Brand: Yolo Electric Pages: 20

Brand: MS ENERGY Pages: 244

Brand: PMG Pages: 9

Brand: JOBO Pages: 48

Brand: Jetson Pages: 24

Brand: Dominator Pages: 8

Brand: Suzuki Pages: 30

Brand: Radio Flyer Pages: 2

Brand: Nova Cruz Pages: 13

Brand: MEGAWHEELS Pages: 80

Brand: KOMFI-RIDER Pages: 20

Brand: Ride VOLO Pages: 16

Brand: Ride VOLO Pages: 18

Brand: Ride1up Pages: 22

Brand: TilGreen Pages: 22

Brand: Malaguti Pages: 282

Brand: Promovec Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands