manualshive.com logo in svg

Yamaha YP125R, Service Manual

The Yamaha YP125R Owner's Manual is a comprehensive guide that provides detailed instructions and information about the operation and maintenance of the Yamaha YP125R. With our user-friendly website, users can easily download this manual for free, ensuring a worry-free ownership experience. Visit manualshive.com to access your free manual today.

Share
Download
background image

RADIATOR (YP250R)

6-8

EAS26380

RADIATOR (YP250R)

Removing the radiator

Order

Job/Parts to remove

Q’ty

Remarks

Radiator cover/Radiator air duct/Bottom cov-
er/Footrest board

Refer to “GENERAL CHASSIS” on page 
4-1.

Coolant

Drain.
Refer to “CHANGING THE COOLANT” on 
page 3-32.

1

Radiator cap

1

2

Coolant reservoir hose

1

3

Coolant reservoir

1

4

Radiator filler hose

1

5

Radiator inlet hose

1

6

Radiator outlet hose

1

7

Radiator fan motor coupler

1

Disconnect.

8

Radiator

1

9

Radiator fan motor

1

For installation, reverse the removal proce-
dure.

(3)

(3)

9

7

(3)

2

3

8

4

1

6

5

10 Nm (1.0 m

•

kgf, 7.2 ft

•

Ibf)

T.R.

7 Nm (0.7 m

•

kgf, 5.1 ft

•

Ibf)

T.R.

7 Nm (0.7 m

•

kgf, 5.1 ft

•

Ibf)

T.R.

7 Nm (0.7 m

•

kgf, 5.1 ft

•

Ibf)

T.R.

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YP125R

Baja motorsports RT50-R Retro Owner'S Manual preview
RT50-R Retro
Brand: Baja motorsports Pages: 45
Segway i180 Replacement Instructions preview
i180
Brand: Segway Pages: 3
KYMCO 50 SUPER 8 2T Specifications preview
50 SUPER 8 2T
Brand: KYMCO Pages: 1
Rebel ZAB0122 User Manual preview
ZAB0122
Brand: Rebel Pages: 32
Acer AES013 User Manual preview
AES013
Brand: Acer Pages: 338
Billow Technology URBAN85 User Manual preview
URBAN85
Brand: Billow Technology Pages: 38
California Go-Ped GTR User Manual preview
GTR
Brand: California Go-Ped Pages: 8
Quantum Rehab Q6 Edge HD Specifications preview
Q6 Edge HD
Brand: Quantum Rehab Pages: 2
Ice Bear PST50-5 Manual preview
PST50-5
Brand: Ice Bear Pages: 38
Earth T-REX SP 27.5INCH 650B HARDTAIL 2021 Manual preview
T-REX SP 27.5INCH 650B HARDTAIL 2021
Brand: Earth Pages: 16
Orthoquad RZ1000 User Manual preview
RZ1000
Brand: Orthoquad Pages: 28
VelectriX Urban Mens 2.0 Instruction Manual preview
Urban Mens 2.0
Brand: VelectriX Pages: 14
Jetson J2000-BLK User Manual preview
J2000-BLK
Brand: Jetson Pages: 24
ZIMX ZX-CORE Manual preview
ZX-CORE
Brand: ZIMX Pages: 9
Peg-Perego FIUS1501G29 Use And Care Manual preview
FIUS1501G29
Brand: Peg-Perego Pages: 24
Peg-Perego Grinta XL Police Chief IGED1030 Use And Care Manual preview
Grinta XL Police Chief IGED1030
Brand: Peg-Perego Pages: 24
Wellstore 294830 Quick Start Manual preview
294830
Brand: Wellstore Pages: 5
TP FERDINAND II Assembly & Operation preview
FERDINAND II
Brand: TP Pages: 2

Brands by name

Popular brands

Load more brands