manualshive.com logo in svg

Yamaha YFZ45YSSH, Owner'S Manual, Page: 123 / 154

Share
Download
Yamaha YFZ45YSSH Owner'S Manual Download Page 123

8-34

8

The clutch lever free play should measure 8.0–
13.0 mm (0.31–0.51 in) as shown. If the free play is
incorrect, adjust it as follows.

1. To increase the clutch lever free play, turn the

clutch lever free play adjusting nut at the
clutch lever in direction (a), and to decrease it,
turn the nut in direction (b).
If the specified free play cannot be obtained,
proceed with the following steps.

2. Fully turn the adjusting nut at the clutch lever

in direction (a) to loosen the clutch cable.

3. Slide the rubber cover back.
4. Loosen the locknut.

5. To increase the clutch lever free play, turn the

clutch lever free play adjusting nut located to-
wards the center of the cable in direction (a),
and to decrease it, turn the nut in direction (b).

6. Tighten the locknut.
7. Slide the rubber cover to its original position.

TIP

If the specified free play cannot be obtained as de-
scribed above or if the clutch does not operate
correctly, have a Yamaha dealer check the internal
clutch mechanism.

 

1. Clutch lever free play
2. Clutch lever free play adjusting nut (clutch lever)

1

(a)

(b)

2

1. Locknut
2. Clutch lever free play adjusting nut (clutch cable)
3. Rubber cover

1

2

3

(b)

(a)

UBW260E0.book  Page 34  Thursday, May 12, 2016  2:28 PM

Summary of Contents for YFZ45YSSH



























































































































































Reviews:

No comments