manualshive.com logo in svg

Yamaha YFZ45YSSH, Owner'S Manual, Page: 113 / 154

Share
Download
Yamaha YFZ45YSSH Owner'S Manual Download Page 113

8-24

8

14. Install the washer onto the air filter element

frame, and then insert the wing bolt into the
hole in the air filter element frame. 

NOTICE:

Be sure to install the washer with its
curved side facing outward as shown.

[ECB00454]

15. Insert the air filter element into the air filter

case, and then tighten the wing bolt.

NOTICE:

 Make sure that the air filter ele-

ment is properly seated in the air filter
case. Never operate the engine with the air
filter element removed. Doing so would al-
low unfiltered air to enter the engine, caus-
ing rapid engine wear and possible engine
damage. Additionally, the fuel injection
system would be affected resulting in poor
engine performance and possible over-
heating.

 [ECB00763]

16. Install the air filter case cover by hooking the

holders onto the air filter case.

1. Air filter element seat

1

1. Washer

1

UBW260E0.book  Page 24  Thursday, May 12, 2016  2:28 PM

Summary of Contents for YFZ45YSSH



























































































































































Reviews:

No comments