Yamaha YFM90RYXJ Owner'S Manual Download

Page: 36 / 132

4-4

3. Tighten the locknut.

Engine speed limiter plate

When the engine speed limiter plate is installed,
engine speed is limited to 4900 r/min. When this
plate is removed, top engine speed (8500 r/min) is
available.
Remove the plate as follows.

1. Remove the seat. (See page 4-12.)
2. Loosen the screws, and then remove the

plate as shown.

3. Tighten the screws.
4. Install the seat.

TIP

Store the engine speed limiter plate with the own-
er’s manual so that it is readily available whenever
you want to reduce top engine speed.

EBU18392

Front brake lever

The front brake lever is located on the right han-
dlebar. To apply the front brake, pull the brake le-
ver toward the handlebar grip.

1. Locknut
2. Adjusting screw
3. No more than 10 mm (0.39 in)

(b)

(a)

1. Screw
2. Engine speed limiter plate

UBD362E0.book Page 4 Tuesday, January 31, 2017 5:10 PM

Summary of Contents for YFM90RYXJ





































































































































Search results

Summary of Contents for YFM90RYXJ

Reviews:

Related manuals for YFM90RYXJ

Brands by name

Popular brands

Yamaha YFM90RYXJ, Owner'S Manual

Search results

Summary of Contents for YFM90RYXJ

Reviews:

Related manuals for YFM90RYXJ

Brands by name

Popular brands