Yamaha YFM90RYXJ Owner'S Manual Download | Manualshive

Page: 104 / 132

background image

8-21

8

4. Tighten the locknut.
5. Slide the rubber covers to their original posi-

tions.

EBU24061

Valve clearance

The valve clearance changes with use, resulting in
improper air-fuel mixture and/or engine noise. To
prevent this from occurring, the valve clearance
must be adjusted by a Yamaha dealer at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU29602

Brakes

Replacement of brake components requires pro-
fessional knowledge. Brake service should be
performed by a Yamaha dealer.

WARNING

EWB02572

Operating with improperly serviced or adjust-
ed brakes could lead to a loss in braking ability
and an accident.

EBU34511

Checking the front and rear brake
shoes

The front and rear brake shoes must be checked
for wear at the intervals specified in the periodic
maintenance and lubrication chart. Without disas-
sembling the brake, this can be performed by
checking the position of the brake lever free play
adjusting bolts or nut.

Front brakes

To check front brake shoe wear, check the posi-
tion of the adjusting bolts. If a bolt extends more
than 12 mm (0.47 in) from its locknut, the brake
shoes need to be replaced.

1. Rubber cover
2. Throttle lever free play adjusting nut
3. Locknut
4. Throttle lever free play

1

3

2

1

4

(b)

(a)

UBD362E0.book Page 21 Tuesday, January 31, 2017 5:10 PM

«
...
102
103
104
105
106
...
»

Summary of Contents for YFM90RYXJ





































































































































Reviews:

No comments

Related manuals for YFM90RYXJ

Brand: Yamaha Pages: 26

Brand: Airstream Pages: 98

Brand: Husqvarna Pages: 64

Brand: Husqvarna Pages: 46

2008 HUV 4213-G

Brand: Husqvarna Pages: 52

Brand: Husqvarna Pages: 56

Brand: Husqvarna Pages: 60

Brand: Husqvarna Pages: 68

Brand: Husqvarna Pages: 57

2007 HUV 4421-D

Brand: Husqvarna Pages: 64

Brand: Blata Pages: 24

Brand: Sakai Pages: 77

Brand: Fort Pages: 88

Brand: Federal Signal Corporation Pages: 140

Brand: Baja motorsports Pages: 89

Brand: Rato Pages: 118

Brand: Access Motor Pages: 59

2005 LT-A700XK5

Brand: Suzuki Pages: 477

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands