Yamaha YFM90RYXJ Owner'S Manual Download Page 115

Page: 115 / 132

8-32

3. Disconnect the negative battery lead first,

then the positive battery lead by removing
their bolt.

NOTICE:

When removing the bat-

tery, the main switch must be off, and the
negative lead must be disconnected be-
fore the positive lead.

[ECB01002]

4. Pull the battery out of its compartment.

NOTICE

ECB00622

Never attempt to open the battery or remove
the battery cell seals, as this would permanent-
ly damage the battery.

To charge the battery



Confirm the recommended charging rate as
specified on the battery itself.



Select a suitable charger and follow the manu-
facturer’s instructions.

NOTICE

ECB00933

To charge a VRLA (valve-regulated lead-acid)
battery, a special battery charger is required.
Using a conventional battery charger will dam-
age the battery.

To store the battery



If the ATV will not be used for more than one
month, remove the battery, fully charge it, and
then place it in a cool, dry place.



If the battery will be stored for more than two
months, check it at least once a month and fully
charge it if necessary.

1. Positive battery lead (red)
2. Negative battery lead (black)
3. Battery
4. Battery band

UBD362E0.book Page 32 Tuesday, January 31, 2017 5:10 PM

Summary of Contents for YFM90RYXJ





































































































































Search results

Summary of Contents for YFM90RYXJ

Reviews:

Related manuals for YFM90RYXJ

Brands by name

Popular brands

Yamaha YFM90RYXJ, Owner'S Manual

Search results

Summary of Contents for YFM90RYXJ

Reviews:

Related manuals for YFM90RYXJ

Brands by name

Popular brands