Yamaha YFM70RY Service Manual Download

Page: 228 / 374

AC MAGNETO AND STARTER CLUTCH

5-35

2. Apply:

• Sealant “1”

(onto the crankshaft position sensor/stator
assembly lead grommet)

3. Install:

• Woodruff key
• AC magneto rotor
• Washer
• AC magneto rotor nut

TIP

• Clean the tapered portion of the crankshaft and

the AC magneto rotor hub.

• When installing the AC magneto rotor, make

sure the woodruff key is properly seated in the
keyway of the crankshaft.

4. Tighten:

• AC magneto rotor nut “1”

TIP

• While holding the AC magneto rotor “2” with

the sheave holder “3”, tighten the AC magneto
rotor nut.

• Do not allow the sheave holder to touch the

projection on the AC magneto rotor.

5. Install:

• Gasket
• AC magneto cover
• AC magneto cover bolts

TIP

Tighten the AC magneto cover bolts in stages,
using a crisscross pattern.

Yamaha bond No. 1215

90890-85505
(Three Bond No.1215®)

AC magneto rotor nut

60 Nm (6.0 m·kg, 43 ft·lb)

Sheave holder

90890-01701

Primary clutch holder

YS-01880-A

AC magneto cover bolt

10 Nm (1.0 m·kg, 7.2 ft·lb)

New

Summary of Contents for YFM70RY























































































































































































































































































































































































Search results

Summary of Contents for YFM70RY

Reviews:

Related manuals for YFM70RY

Brands by name

Popular brands

Yamaha YFM70RY, Service Manual

Search results

Summary of Contents for YFM70RY

Reviews:

Related manuals for YFM70RY

Brands by name

Popular brands