Yamaha YFM70RSBG Owner'S Manual Download

Page: 151 / 160

10-1

EBU25962

SPECIFICATIONS

Dimensions:

Overall length:

1845 mm (72.6 in)

Overall width:

1155 mm (45.5 in)

Overall height:

1115 mm (43.9 in)

Seat height:

830 mm (32.7 in)

Wheelbase:

1280 mm (50.4 in)

Ground clearance:

240 mm (9.4 in)

Minimum turning radius:

3500 mm (138 in)

Weight:

Curb weight:

192.0 kg (423 lb)

Noise and vibration level:

Noise level (77/311/EEC):

84.0 dB(A) at 3125 r/min (YFM70RSBG_EUR/FRA/GBR,
YFM70RSSG_EUR/FRA/GBR)

Uncertainty of measurement:

3.0 dB(A) (YFM70RSBG_EUR/FRA/GBR,
YFM70RSSG_EUR/FRA/GBR)

A-weighted sound power level:

97.0 dB(A) at 3125 r/min (YFM70RSBG_EUR/FRA/GBR,
YFM70RSSG_EUR/FRA/GBR)

Uncertainty of measurement:

3.0 dB(A) (YFM70RSBG_EUR/FRA/GBR,
YFM70RSSG_EUR/FRA/GBR)

Vibration on seat (EN1032, ISO5008):

0.7 m/s² (YFM70RSBG_EUR/FRA/GBR,
YFM70RSSG_EUR/FRA/GBR)

Uncertainty of measurement:

0.6 m/s² (YFM70RSBG_EUR/FRA/GBR,
YFM70RSSG_EUR/FRA/GBR)

Vibration on handle (EN1032, ISO5008):

4.7 m/s² (YFM70RSBG_EUR/FRA/GBR,
YFM70RSSG_EUR/FRA/GBR)

Uncertainty of measurement:

0.5 m/s² (YFM70RSBG_EUR/FRA/GBR,
YFM70RSSG_EUR/FRA/GBR)

Engine:

Engine type:

Liquid cooled 4-stroke, SOHC

Cylinder arrangement:

Single cylinder

Displacement:

686 cm³

Bore

stroke:

102.0

84.0 mm (4.02

3.31 in)

Compression ratio:

10.0 : 1

Starting system:

Electric starter

U2LS61E0.book Page 1 Friday, April 17, 2015 8:25 AM

Summary of Contents for YFM70RSBG

































































































































































Search results

Summary of Contents for YFM70RSBG

Reviews:

Related manuals for YFM70RSBG

Brands by name

Popular brands

Yamaha YFM70RSBG, Owner'S Manual

Search results

Summary of Contents for YFM70RSBG

Reviews:

Related manuals for YFM70RSBG

Brands by name

Popular brands