Yamaha YFM35FGIY Owner'S Manual Download | Manualshive

Page: 46 / 166

background image

5-5

5

EBU19802

Tires

WARNING

EWB00552

POTENTIAL HAZARD
Operating this ATV with improper tires, or
with improper or uneven tire pressure.
WHAT CAN HAPPEN
Use of improper tires on this ATV, or opera-
tion of this ATV with improper or uneven tire
pressure, may cause loss of control, in-
creasing your risk of accident.
HOW TO AVOID THE HAZARD

●

The tires listed below have been approved
by Yamaha Motor Manufacturing Corpora-
tion of America for this model. Other tire
combinations are not recommended.
Front:

Manufacturer/model:

MAXXIS/M979

Size:

AT25 x 8-12

Type:

Tubeless

Rear:

Manufacturer/model:

MAXXIS/M980

Size:

AT25 x 10-12

Type:

Tubeless

●

The tires should be set to the recommend-
ed pressure:
Recommended tire pressure:

Front:

25.0 kPa (0.250 kgf/cm², 3.6 psi)

Rear:

25.0 kPa (0.250 kgf/cm², 3.6 psi)

• Check and adjust tire pressures when

the tires are cold.

• Tire pressures must be equal on both

sides.

U4S212E0.book Page 5 Thursday, April 17, 2008 9:17 AM

«
...
44
45
46
47
48
...
»

Summary of Contents for YFM35FGIY







































































































































































Reviews:

No comments

Related manuals for YFM35FGIY

Brand: KAYO MOTO Pages: 6

Brand: Ace Sports Pages: 79

Brand: LaTrax Pages: 36

Brand: Yamaha Pages: 59

DOC ECO 30NXMOPRPB001

Brand: Nilox Pages: 84

WILD HP 300 - SERVICE

Brand: GAS GAS Pages: 65

1970 SKI-DADDLER

Brand: AMF Pages: 74

Brand: Dcm Pages: 14

ErgoSteer SP001V9810010

Brand: FENDT Pages: 40

Brand: Suzuki Pages: 139

Brand: Satellite Suites Pages: 39

Brand: Tractor Supply Pages: 102

Vyper 4WD 1100cc

Brand: gio Pages: 113

545 XC ATV EU 2011

Brand: KTM Pages: 221

VIPER 50 ST - SERVICE

Brand: E-TON Pages: 68

Brand: Kärcher Pages: 346

Brand: NC Pages: 84

Brand: HAUL MASTER Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands