Yamaha YFM350RB Page 90 Owner'S Manual Download

Page: 90 / 140

8-10

TIP
If the spark plug shows a distinctly different color,
the engine could be operating improperly. Do not
attempt to diagnose such problems yourself. In-
stead, have a Yamaha dealer check the ATV.

2. Check the spark plug for electrode erosion

and excessive carbon or other deposits, and
replace it if necessary.

3. Measure the spark plug gap with a wire thick-

ness gauge and, if necessary, adjust the gap
to specification.

To install the spark plug

1. Clean the surface of the spark plug gasket

and its mating surface, and then wipe off any
grime from the spark plug threads.

2. Install the spark plug with the spark plug

wrench, and then tighten it to the specified
torque.

Specified spark plug:

NGK/DR8EA

1. Spark plug gap

Spark plug gap:

0.6–0.7 mm (0.024–0.028 in)

U1BS62E0.book Page 10 Monday, April 18, 2011 6:43 PM

Summary of Contents for YFM350RB













































































































































Search results

Summary of Contents for YFM350RB

Reviews:

Related manuals for YFM350RB

Brands by name

Popular brands

Yamaha YFM350RB, Owner'S Manual

Search results

Summary of Contents for YFM350RB

Reviews:

Related manuals for YFM350RB

Brands by name

Popular brands