Yamaha YFM350RB Owner'S Manual Download | Manualshive

Page: 108 / 140

background image

8-28

8

The brake light switch for the brake pedal can be
adjusted as follows, but the front brake light switch
should be adjusted by a Yamaha dealer.
Turn the rear brake light switch adjusting nut while
holding the brake light switch in place. To make the
brake light come on earlier, turn the adjusting nut
in direction (a). To make the brake light come on
later, turn the adjusting nut in direction (b).

EBU30120

Adjusting the clutch lever free play

The clutch lever free play must be checked and, if
necessary, adjusted at the intervals specified in the
periodic maintenance and lubrication chart.

The clutch lever free play should measure 5.0–
10.0 mm (0.20–0.39 in) as shown. If the free play
is incorrect, adjust it as follows.

1. Slide the rubber cover back at the clutch lever.
2. Loosen the locknut.
3. To increase the clutch lever free play, turn the

adjusting bolt at the clutch lever in direction
(a), and to decrease it, turn the bolt in direction
(b).

1. Rear brake light switch
2. Rear brake light switch adjusting nut

1. Clutch lever free play

2. Rubber cover

3. Locknut
4. Clutch lever free play adjusting bolt

3

2

4

(a)

(b)

1

U1BS62E0.book Page 28 Monday, April 18, 2011 6:43 PM

«
...
106
107
108
109
110
...
»

Summary of Contents for YFM350RB













































































































































Reviews:

No comments

Related manuals for YFM350RB

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands