Yamaha YFM25RB Owner'S Manual Download Page 89

Page: 89 / 134

8-12

6. Insert the dipstick into the oil filler hole, and

then tighten the engine oil filler cap.

To change the engine oil (with or without oil fil-
ter element replacement)

1. Place the ATV on a level surface.
2. Start the engine, warm it up for several min-

utes, and then turn it off.

3. Place an oil pan under the engine to collect

the used oil.

4. Remove the engine oil filler cap, and then re-

move the engine oil drain bolt and its gasket to
drain the oil from the crankcase.

TIP
Skip steps 5–7 if the oil filter element is not being
replaced.

5. Remove the oil filter element cover by remov-

ing the bolts, and then remove the oil filter el-
ement and the O-rings.

1. Engine oil drain bolt
2. Gasket

1. Oil filter element cover
2. Bolt

U1BT62E0.book Page 12 Tuesday, April 19, 2011 7:06 PM

Summary of Contents for YFM25RB







































































































































Search results

Summary of Contents for YFM25RB

Reviews:

Related manuals for YFM25RB

Brands by name

Popular brands

Yamaha YFM25RB, Owner'S Manual

Search results

Summary of Contents for YFM25RB

Reviews:

Related manuals for YFM25RB

Brands by name

Popular brands