Yamaha YFM25RB Owner'S Manual Download Page 113

Page: 113 / 134

8-36

KEEP OUT OF REACH OF CHILDREN.

NOTICE

ECB00620

Never attempt to remove the battery cell seals,
as this would permanently damage the battery.

To remove the battery

1. Remove the seat. (See page 4-11.)
2. Unhook the band securing the owner’s tool kit,

and then remove the battery holding plate by
removing the bolts.

3. Disconnect the negative battery lead first,

then the positive battery lead by removing
their bolt. NOTICE: When removing the bat-
tery, the main switch must be off, and the
negative lead must be disconnected be-
fore the positive lead.

[ECB01001]

4. Pull the battery out of its compartment.

1. Battery holding plate

2. Bolt

1. Negative battery lead (black)
2. Positive battery lead (red)

U1BT62E0.book Page 36 Tuesday, April 19, 2011 7:06 PM

Summary of Contents for YFM25RB







































































































































Search results

Summary of Contents for YFM25RB

Reviews:

Related manuals for YFM25RB

Brands by name

Popular brands

Yamaha YFM25RB, Owner'S Manual

Search results

Summary of Contents for YFM25RB

Reviews:

Related manuals for YFM25RB

Brands by name

Popular brands