Yamaha XT660R Owner'S Manual Download

Page: 72 / 92

PERIODIC MAINTENANCE AND MINOR REPAIR

6-34

fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with al-
cohol or thinner.

5. Install the bulb cover, and then

connect the coupler.

6. Install the cowling together with

the headlight unit.

7. Have a Yamaha dealer adjust the

headlight beam if necessary.

EAU24281

Replacing a turn signal light
bulb or the tail/brake light bulb

1. Remove the lens by removing the

screws.

2. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws.

CAUTION:

ECA10680

Do not overtighten the screws, oth-
erwise the lens may break.

1. Do not touch the glass part of the bulb.

1. Screw

U5VKE1E0.book Page 34 Tuesday, July 18, 2006 1:00 PM

Summary of Contents for XT660R





























































































Search results

Summary of Contents for XT660R

Reviews:

Related manuals for XT660R

Brands by name

Popular brands

Yamaha XT660R, Owner'S Manual

Search results

Summary of Contents for XT660R

Reviews:

Related manuals for XT660R

Brands by name

Popular brands