manualshive.com logo in svg

Yamaha XL700 WaveRunner 2004, Owner'S/Operator'S Manual, Page: 96 / 120

Share
Download
Yamaha XL700 WaveRunner 2004 Owner'S/Operator'S Manual Download Page 96

4-15

E

NOTE:

@ 

●

Wipe off any water on the spark plug or
inside the cap before installing the spark
plug cap. Push the spark plug cap down
until it clicks. 

●

If a torque wrench is not available when
you are fitting a new spark plug, a good
estimate of the correct torque is 1/4 turn
to 1/2 turn past finger tight. Have the
spark plug adjusted to the correct torque
with a torque wrench as soon as possible. 

@ 

WARNING

@ 

Be careful not to damage the insulator
when removing or installing a spark plug.
A damaged insulator could allow sparks
to escape, which could lead to explosion
or fire. 

@

EJU11391 

Lubrication points 

To keep moving parts sliding or rotating

smoothly, coat them with water-resistant
grease.

Recommended water-resistant grease: 

Yamaha Marine Grease/ 
Yamaha Grease A

●

Throttle cable (carburetor end) 

●

Choke cable (carburetor end) 

UF0M15.book  Page 15  Tuesday, June 3, 2003  3:36 PM

Summary of Contents for XL700 WaveRunner 2004

























































































































Reviews:

No comments