manualshive.com logo in svg

Yamaha XL700 WaveRunner 2004, Owner'S/Operator'S Manual, Page: 110 / 120

Share
Download
Yamaha XL700 WaveRunner 2004 Owner'S/Operator'S Manual Download Page 110

5-5

E

EJU01882

Connecting the jumper cables 

1. Connect the positive (+) jumper cable 

1

to the positive (+) terminals of both bat-
teries. 

2. Connect one end of the negative (–)

jumper cable 

2

 to the negative (–) termi-

nal of the booster battery 

3

. 

3. Connect the other end of the negative (–)

cable to an unpainted bolt on the cylinder
head.

CAUTION:

@ 

Do not connect the end of the jumper
cable to the negative (–) terminal on the
watercraft battery! Be sure all connec-
tions are secure and correct before
attempting to start the engine. Any
wrong connection may damage the elec-
trical system. 

@

4. Start the engine, and then disconnect

the cables by reversing the steps above.

CAUTION:

@ 

●

Never push the start switch while the
engine is running. 

●

Do not operate the start switch for
more than 5 seconds, otherwise the
battery will be discharged and the
engine will not start. Also, the starter
motor may be damaged. If the engine
does not start in 5 seconds, release
the start switch, wait 15 seconds, and
try again. 

@

UF0M15.book  Page 5  Tuesday, June 3, 2003  3:36 PM

Summary of Contents for XL700 WaveRunner 2004

























































































































Reviews:

No comments