Yamaha XL700 WaveRunner 2001 Owner'S/Operator'S Manual Download Page 63 | Manualshive

Page: 63 / 120

background image

3-18

E

5. While lightly squeezing the throttle lever,

push the start switch (green button).

WARNING

@

On this watercraft, the engine is con-
nected directly to the jet pump. Starting
the engine immediately generates some
thrust. Apply only enough throttle to
keep the engine running.

@

6. Release the start switch as soon as the

engine starts to run.

CAUTION:

@

●

Never push the start switch while the
engine is running.

●

Do not operate the start switch for
more than 5 seconds, otherwise the
battery will be discharged and the
engine will not start. Also, the starter
motor may be damaged. If the engine
does not start in 5 seconds, release
the start switch, wait 15 seconds, and
try again.

@

7. After the engine has warmed up, push

the choke knob in to its original position.

NOTE:

@

If the choke knob is left pulled out, the
engine will stall.

@

UF0M15.book Page 18 Tuesday, June 3, 2003 3:36 PM

«
...
61
62
63
64
65
...
»

Summary of Contents for XL700 WaveRunner 2001

























































































































Reviews:

No comments

Related manuals for XL700 WaveRunner 2001

Brand: PURSUIT Pages: 154

Brand: COBIA Pages: 39

Brand: Cobalt Digital Inc Pages: 136

mirage Pro Angler

Brand: Hobie Pages: 28

Brand: Hobie Pages: 36

Brand: Sea-doo Pages: 156

Brand: GALA Pages: 10

Brand: CORRECT CRAFT Pages: 188

Brand: CORRECT CRAFT Pages: 192

Brand: Mercury Pages: 522

S4 Standup 2007

Brand: HSR Pages: 134

Brand: BENETEAU Pages: 114

Brand: UIM Pages: 17

Brand: Lagoon Pages: 30

Brand: Jeanneau Pages: 97

SUN ODYSSEY 50DS

Brand: Jeanneau Pages: 156

Brand: Intex Pages: 13

Brand: Ranger Tugs Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands