Yamaha XL700 WaveRunner 2001 Owner'S/Operator'S Manual Download Page 41 | Manualshive

Page: 41 / 120

background image

2-14

E

EJU01132

Oil level warning lamp

If the oil remaining in the tank drops to

about 1.2 L (0.31 US gal, 0.26 Imp gal) or
the oil filter is clogged, the oil level warning
lamp begins to blink.

If the oil level warning lamp begins to

blink, refill with engine oil as soon as possi-
ble.

NOTE:

@

●

The lamp will light up for 2 seconds after
starting the engine to check the lamp
operation.

●

If the warning lamp blinks with adequate
oil in the tank, check for a clogged oil fil-
ter.

@

UF0M15.book Page 14 Tuesday, June 3, 2003 3:36 PM

«
...
39
40
41
42
43
...
»

Summary of Contents for XL700 WaveRunner 2001

























































































































Reviews:

No comments

Related manuals for XL700 WaveRunner 2001

Brand: Jeanneau Pages: 15

Brand: SeaDoo Pages: 39

Brand: Sea-doo Pages: 15

Brand: Sea Ray Boats Pages: 26

Brand: Sea Eagle Boats Pages: 8

Brand: Sea Eagle Pages: 13

Brand: Sea Ray Pages: 80

Brand: Sea-doo Pages: 202

Brand: Sea-doo Pages: 314

Brand: Ritzy Charters Pages: 15

Brand: Everglades Pages: 126

Brand: Baja Pages: 87

Brand: Meridian Yachts Pages: 100

Brand: Topper Pages: 13

Brand: Topper Pages: 14

Brand: Topper Pages: 15

Brand: Topper Pages: 16

Brand: Topper Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands